Bosch Appliances Home Security System D1260B Manuel D’Utilisation
D1260/D1260B | Owner's Manual | Part IV: Multi-Area Use - Working with Multiple Areas from a Single Command
Center
Center
68
Bosch Security Systems | 9/04 | 50410D
Part IV: Multi-Area Use
Working with Multiple Areas from a Single
Command Center
Each of the functions described in the preceding
section on Advanced Commands is presented as
though your system includes only one area. If your
system includes more than one area, it can be set up in
one of two ways by the installing company:
section on Advanced Commands is presented as
though your system includes only one area. If your
system includes more than one area, it can be set up in
one of two ways by the installing company:
•
Each command center will only have access to the
local area to which it is assigned, or
local area to which it is assigned, or
•
Each command center may access either some or
all areas beyond the one to which it is assigned.
This factor is referred to hereafter as
all areas beyond the one to which it is assigned.
This factor is referred to hereafter as
command
center scope.
If your command center allows access to areas other
than the local area (that is to say, has scope in other
areas), then the command center will limit your access
to those areas within the command center scope and
for which your personal passcode has authority.
than the local area (that is to say, has scope in other
areas), then the command center will limit your access
to those areas within the command center scope and
for which your personal passcode has authority.
Given that you have access to areas beyond the local
area, the means of accessing the various system
functions depends upon the specific function.
area, the means of accessing the various system
functions depends upon the specific function.
For some functions, the command center allows you to
select the area (or point) in which to perform the
function. These “selectable” functions are:
select the area (or point) in which to perform the
function. These “selectable” functions are:
•
DISARM ?,
•
MASTER ARM AREA ?.
•
BYPASS A POINT? and
•
UNBYPASS A POINT?
Another group of functions may automatically work in
all areas in which you have passcode authority and
which are within the scope of the command center.
These are:
all areas in which you have passcode authority and
which are within the scope of the command center.
These are:
•
Turning On Multiple Areas with a Passcode,
•
Turning Off Multiple Areas with a Passcode,
•
DISARM ALL ?,
•
MASTER ARM ALL?,
•
VIEW MEMORY?,
•
WALK TEST?,
•
RESET SENSORS ?,
•
ADD PASSCODES ?,
•
FIRE TEST?,
•
VIEW POINT STATUS? and
•
VIEW AREA STATUS?
Some functions may be area-specific. To perform these
functions, you must first use the MOVE TO AREA ?
function (Command 50) to gain access to the desired
area. Once in the desired area you can perform the
functions you wish. Area-specific functions include:
functions, you must first use the MOVE TO AREA ?
function (Command 50) to gain access to the desired
area. Once in the desired area you can perform the
functions you wish. Area-specific functions include:
•
PERIMETR INST? (Perimeter On Instant),
•
PERIMETR DELAY ? (Perimeter On Delay),
•
PERIMETR PART ? (Perimeter On Partial),
•
EXTEND CLOSING ?,
•
WATCH MODE ?,
•
COMMAND 7 ?,
•
COMMAND 9 ? and
•
CHG DISPLAY ?.
A last group of functions don’t relate to specific areas
and are thus system-wide. These are:
and are thus system-wide. These are:
•
SEND REPORT?,
•
REMOTE PROG ?,
•
CHG TIME/DATE ?,
•
CHG SKEDS ?,
•
DEL PASSCODES ?,
•
CHG RELAYS ?,
•
CHG PASSCODES ?,
•
PRINT LOG ? and
•
VIEW LOG?
View Area Status
Use this function when you need to know the status
(whether armed or disarmed) of areas other than the
one you’re in.
(whether armed or disarmed) of areas other than the
one you’re in.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the
Menu>
key to enter the Command
Menu.
3.
Press
Next>
repeatedly until you reach the
VIEW
AREA STAT ?>
prompt.
Press the adjacent soft key.