Behringer Musical Instrument Amplifier FBQ3102 Manuel D’Utilisation

Page de 12
6
ULTRAGRAPH PRO FBQ1502/ULTRAGRAPH PRO FBQ3102/ULTRAGRAPH PRO FBQ6200
a unit intended for the European market to a 120 V power
outlet, you must also replace the factory fuse with a higher-
value  fuse.
SERIAL NUMBER. Please take a few minutes and send to
us a completely filled out warranty card within 14 days of
the original date of purchase. Otherwise, warranty claims
may be rendered invalid. Or fill out the warranty information
online  at  www.behringer.com.
Fig. 2.3: Connectors at the rear of the FBQ3102
INPUT.  These  are  the  audio  inputs  of  the  FBQ3102.  All
three equalizers in the series feature the same input and
output  connectors  in  the  form  of  balanced  1/4"  TRS  and
XLR  connectors.
OUTPUT. These are the audio outputs. The 1/4" connectors
and their respective XLR connectors are wired in parallel.
SUB  OUT.  This  balanced  XLR  connector  provides  the
output  signal  for  your  subwoofer.  A  summed  up  mono
signal for the subwoofer is provided here. Please connect
the subwoofer amplifier’s input to this connector.
Use  the  X-OVER  FREQ  control  to  select  the  desired
crossover  frequency  for  the  subwoofer.
+
The  bandwidth  limitation  enacted  through  the  high-
pass  filter  (LOW  CUT)  also  affects  the  frequency
response  of  the  subwoofer  output.
2.3 Additional FBQ6200 control elements
2.3.1 Limiter
One  of  the  FBQ6200’s  outstanding  features  is  its  integrated
limiter.
A limiter is a device that protects your loudspeakers and other
equipment  connected  to  your  FBQ6200  (or  your  recordings)
from overdriving and the signal distortion associated.
+
Please  take  into  consideration  that  when  you
increase  the  presence  of  multiple  frequency  bands,
the  overall  signal  level  increases  substantially  as
well.  The  limiter  will  process  very  quickly  in  such
situations. This can be avoided by performing signal
corrections  by  lowering  certain  frequency  ranges
instead  of  increasing  others.
To  produce  creative  sound  effects,  you  can  also
purposely  “force”  the  peak  limiter  into  action.
The ULTRAGRAPH PRO FBQ6200 features a built-in limiter
for each channel. Use the LIMITER switch for its activation.
Fig.  2.4:  FBQ6200  control  elements
The limiter display informs you about the amount of gain
reduction perfomed by the limiter.
The limiter confines the signal to an adjustable signal level.
Use the THRESHOLD control to adjust the threshold value
of the limiter from -6 to +22 dB. When the control is in the
“-6 dB” setting, the gain reduction is very pronounced; the
more you turn the control toward “+22 dB”, the gain reduction
is  lower.  When  the  threshold  control  is  in  its  right-most
position, the limiter is not applied.
2.3.2 Noise generator
By using the built-in noise generator, you can create the so-
called “pink noise” that can be used to adjust your P.A. system to
specific  acoustic  characteristics  of  various  venues.
Activate the pink noise generator by using the PINK NOISE
switch. The built-in switch illumination blinks red when the
pink noise generator is activated.
Read  off  the  noise  generator’s  signal  level  on  the  LED
display.
Use the NOISE LEVEL control to adjust the volume of the
pink noise you generate.
Room  resonance  and  sound  transfer  characteristics  of  the
P.A.  system  cause  some  frequencies  to  be  more  prominently
present while other frequencies are less present. Pink noise is a
neutral  signal  that  can  be  played  back  via  the  P.A.  system in
order  to  measure  these  sound  characteristics.
Such  a  measurement  of  the  frequency  response  by  using  a
special  microphone  in  conjunction  with  a  real-time  analyzer (a
real-time analyzer is for example integrated into the BEHRINGER
ULTRACURVE PRO DEQ2496) delivers the basis for setting up
the  equalizer.  More  pronounced  frequencies  are  lowered,  and
those  frequencies  that  are  not  so  prominently  featured  are
increased, thus approximately achieving linear reproduction.
2. CONTROL ELEMENTS AND CONNECTORS