Bullard PA1 Manuel D’Utilisation
TM
Tr
o
ubleshooting/Cleaning and Stor
age
7
Troubleshooting
The following guide will enable you to locate and correct malfunctions:
Possible Cause
Solution
Battery charging port plug not in position
Install charging port plug.
Low Battery
Re-charge battery.
Air inlet to hood is twisted
Remove and reinsert PA1BT breathing
tube 5" into hood inlet.
tube 5" into hood inlet.
Clogged/damaged air-purifying
Replace the filter and gasket.
filter element
Battery low
Re-charge battery.
Blower malfunction
Replace blower.
Breathing tube or hood damaged
Replace breathing tube and/or hood.
Shipping card not removed
Remove card and install filter &
gasket.
gasket.
Equipment damaged or filter
Leave hazardous area immediately
needs to be replaced
and check equipment. Replace filter.
If the problem persists and no
damage is found, return equipment
for repair.
If the problem persists and no
damage is found, return equipment
for repair.
Low airflow
See above.
Improper initial charge
Review “Initial Charging Procedure”
Prolonged storage of unit not on charger
on page 4.
Malfunction
No power
PA1BU Low Battery Alarm is
sounding, but Airflow Indicator
shows adequate air flow
sounding, but Airflow Indicator
shows adequate air flow
No/low airflow into covering
(Alarm sounding for low battery in
PA1BU unit)
(Alarm sounding for low battery in
PA1BU unit)
Smell or taste contaminant
Blower Unit does not run for
full service life
(10 hours - PA1, 6 hours - PA2)
full service life
(10 hours - PA1, 6 hours - PA2)
Cleaning
Avoid contaminant entry into the breathing tube, as this
will compromise respiratory protection and could result
in death or serious injury. Consult your local safety
professional if you suspect that contaminant has entered
the breathing tube. When cleaning the equipment, do the
following:
will compromise respiratory protection and could result
in death or serious injury. Consult your local safety
professional if you suspect that contaminant has entered
the breathing tube. When cleaning the equipment, do the
following:
Ensure water does not enter filter. Replace wet filter.
DO NOT use gasoline, organic-based solvents, or
chlorinated degreasing fluids (such as trichloroethylene)
as they will cause damage.
chlorinated degreasing fluids (such as trichloroethylene)
as they will cause damage.
DO NOT immerse the equipment in water or other
cleaning fluid as this may cause contamination in the
breathing tube and blower interior that will be difficult to
remove.
cleaning fluid as this may cause contamination in the
breathing tube and blower interior that will be difficult to
remove.
Failure to observe the instructions and warnings in this
manual invalidates all performance statements and
approvals for this equipment and could result in death or
serious injury.
manual invalidates all performance statements and
approvals for this equipment and could result in death or
serious injury.
Use a lint-free cloth moistened in a mild solution of soap
and warm water to clean the outer surface of the
equipment.
and warm water to clean the outer surface of the
equipment.
Consult the CC20/PA20 Series Tychem Hood User Manual
for cleaning instructions for the hood components. Remove
filter and discard (if it has reached the end of its useful life)
in accordance with federal, state and local guidelines and
in conformance with plant safety regulations.
for cleaning instructions for the hood components. Remove
filter and discard (if it has reached the end of its useful life)
in accordance with federal, state and local guidelines and
in conformance with plant safety regulations.
Re-charge the battery pack (see instructions on page 3).
Storage
When the apparatus is completely dry, store in a clean, dry
area, away from direct sunlight and sources of direct heat.
area, away from direct sunlight and sources of direct heat.
The storage temperature should be between 32º F to 90º F
(0º C to 32º C) with humidity less than 90% RH.
(0º C to 32º C) with humidity less than 90% RH.
Consult the CC20/PA20 Series Tychem Hood User Manual
for storage instructions on hood components.
for storage instructions on hood components.
WARNING