Manualsbrain.com
  1. Manuels
  2. Marques
  3. Blue Sea Systems
  4. Portable Generator 120 V Ac ELCI MAin Panels
  5. Fascicule

Blue Sea Systems Portable Generator 120 V Ac ELCI MAin Panels Fascicule

Télécharger
Page de 2
ADDITIONAL BREAKER 
REQUIRED IF GREATER 
THAN 10 FEET
CONNECT 
TO AC HOT 
LOAD(S)
NEUTRAL
PIGTAIL
LINE 
1
LOAD 
1
N
N
SENSOR COIL
TO AC SAFETY GROUND SOURCE
DC BACKLIGHT
BOARD
FROM DEVICE
SAFETY
GROUND
FROM DEVICE
NEUTRAL
FUSE 1.0 TO 2.0A
AC SAFETY
GROUND BUS
AC NEUTRAL
 BUS
R.P.
LED
LED
FROM AC HOT SOURCE
FROM AC NEUTRAL SOURCE
SHORE 
POWER
INLET
Installation
(continued)
 
4.  Install feed circuit wires
Install the feed wires from the shore power inlet or other AC source, 
referring to the wire sizing chart to select the correct wire size. Connect 
the black AC hot, white AC neutral and green AC safety ground as 
shown in the illustration.
If the feed wires are from the shore power inlet or the electrical 
attachment point of a permanently installed shore power cord and the 
inlet or attachment point is more than 10 feet from this panel, additional 
fuses or circuit breakers must be installed within 10 feet of the shore 
power inlet. The measurement is made along the conductors.
5.  Installation of Backlight System
 
The backlight board is a DC device. When installing it in an AC panel  
 
both wire leads must be connected to an appropriate DC source 
 
and ground.
 
Connect the yellow negative wire to a DC ground. Connect the red  
 
positive wire to a DC positive supply, usually a switch that controls  
 
the vessel’s other nighttime illumination.
6.  Apply branch circuit labels and mount panel
Apply a label for each circuit from the label set provided. Extended 
label sets are available through retail suppliers, and over 500 individual
labels are available directly from Blue Sea Systems. Please go to
www.bluesea.com to order individual labels for specific applications.
Fasten the panel to the mounting surface using the screws provided.
7.  Testing
  Connect the vessel’s shore power and verify the Reverse Polarity 
light is not illuminated. If the red Reverse Polarity light is on then 
either the hot and ground or the hot and neutral wires have been 
crossed. Starting at the panel, trace the connections back as far as 
necessary to locate the error.
  Using a multimeter where the power source is connected to the
 
panel verify:
 
  a.  120 volts between hot and neutral
 
   
(nominal, this may vary depending on source voltage) 
 
  b.  120 volts between hot and ground.
 
  c.  0 volts between neutral and ground.
  Turn on each branch circuit to verify power to each circuit.
 
Refer to Carling Technologies™ PB-Series ELCI/RCBO installation
 
Bulletin for Marine Main Circuit Protection, (IST-0006), for test 
 
procedure and frequency.
8.  Optional Branch LEDs
 
This Panel is supplied with LEDs pre-installed in all optional branch  
 
positions. For future expansion of the panel remove the hot leg of the  
 
LED from the AC Neutral Bus and connect it to the Load side of the  
 
branch circuit breaker.
Note
 
 
Blue Sea Systems’ 8101 and 8102 electrical distribution panels 
 
are furnished with two 15A AC branch circuits. This rating will satisfy 
 
the vast majority of marine circuit protection situations.
Related Products from Blue Sea Systems
• 360 Panel System
• Battery management solutions
• AC and DC circuit protection devices
• WeatherDeck™ waterproof circuit breaker panels
• Fuses, fuse blocks, and BusBars
• Analog and digital meters
Useful Reference Books
• Calder, Nigel (2005). Boatowner’s Mechanical and Electrical Manual 
 
  (3d ed). Camden ME: International Marine / McGraw-Hill.
• Wing, Charlie (2206). Boatowner’s Illustrated Electrical Handbook  
 
  (2d ed). Camden ME: International Marine / McGraw-Hill.
Keep all supplied instructions with boat system records
for future reference.
ADDITIONAL BREAKER 
REQUIRED IF GREATER 
THAN 10 FEET
LINE 
1
LOAD 
1
N
N
SENSOR COIL
TO AC SAFETY GROUND SOURCE
DC 
BACKLIGHT
BOARD
FROM
DEVICE
SAFETY
GROUND
FROM
DEVICE
SAFETY
GROUND
FROM
DEVICE
NEUTRAL
R.P.
LED
LED
LED
LED
LED
LED
LED
AC SAFETY GROUND BU
S
AC NEUTRAL BU
S
FROM AC HOT SOURCE
FROM AC NEUTRAL SOURCE
SHORE 
POWER
INLET
NEUTRAL
PIGTAIL
TO DC
NEGATIVE
FROM DC
POSITIVE
TO DEVICE
HOT
TO DEVICE
HOT
15A
15A
BRANCH
CIRCUIT
R.P.
LED
FUSE
DC 
BACKLIGHT
BOARD
1.0 TO 2.0A
AC
VOLTMETER
+12V
+24V
-Neg
Red
Orange
Yellow
LED
LED
LED
LINE 
1
LOAD 
1
N
N
AC NEUTRAL BU
S
FROM
DEVICE
NEUTRAL
SENSOR COIL
TO AC SAFETY GROUND SOURCE
FROM AC HOT SOURCE
FROM AC NEUTRAL SOURCE
SHORE 
POWER
INLET
ADDITIONAL BREAKER 
REQUIRED IF GREATER 
THAN 10 FEET
NEUTRAL
PIGTAIL
FROM
DEVICE
SAFETY
GROUND
AC SAFETY GROUND BU
S
Wiring Diagram PN 8102 - 120V AC ELCI Panel, 30A Main, 2 Position, Voltmeter
Wiring Diagram PN 8101 - 120V AC ELCI Panel, 30A Main, 5 Position
Wiring Diagram PN 8100 - 120V AC ELCI Panel, 30A Main