Whirlpool W10196160D Manuel D’Utilisation
10
3. You can check the burner flame by removing the flame
spreader or by using a mirror.
Remove flame spreader:
Remove 2 screws from the front tabs of the flame spreader.
Lift front of the flame spreader and pull forward to remove
tabs from rear of oven.
Remove flame spreader:
Remove 2 screws from the front tabs of the flame spreader.
Lift front of the flame spreader and pull forward to remove
tabs from rear of oven.
Using a mirror:
Insert a mirror to one side of the burner. Look into the mirror to
check flame.
Insert a mirror to one side of the burner. Look into the mirror to
check flame.
4. Push the BAKE pad.
5. Press the START pad.
5. Press the START pad.
The oven bake burner should light within 8 seconds. Under
certain conditions it may take the burner up to 50 to 60 seconds
to light.
Electronic igniters are used to light the bake and broil burners.
Refer to the Use and Care Guide for proper operation of the oven
controls.
certain conditions it may take the burner up to 50 to 60 seconds
to light.
Electronic igniters are used to light the bake and broil burners.
Refer to the Use and Care Guide for proper operation of the oven
controls.
Adjust Oven Bake Burner Flame (if needed)
1. On models with a warming drawer, remove access cover plate
(1 screw) located at the back of the warming drawer
compartment.
compartment.
2. Check the oven bake burner for proper flame.
This flame should have a ½" (1.3 cm) long inner cone of
bluish-green, with an outer mantle of dark blue, and should be
clean and soft in character. No yellow tips, blowing or lifting of
flame should occur.
bluish-green, with an outer mantle of dark blue, and should be
clean and soft in character. No yellow tips, blowing or lifting of
flame should occur.
3. If the oven bake flame needs to be adjusted, locate the air
shutter near the center rear of the range. Loosen the locking
screw and rotate the air shutter until the proper flame appears.
Tighten locking screw.
screw and rotate the air shutter until the proper flame appears.
Tighten locking screw.
4. Push CANCEL/OFF when finished.
5. Reinstall flame spreader and oven bake burner cover.
5. Reinstall flame spreader and oven bake burner cover.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press the BROIL pad.
3. Press the START pad.
The oven burner should light within 8 seconds. Under certain
conditions it may take the burner up to 50 to 60 seconds to light.
Refer to the Use and Care Guide for proper operation of the oven
controls.
2. Press the BROIL pad.
3. Press the START pad.
The oven burner should light within 8 seconds. Under certain
conditions it may take the burner up to 50 to 60 seconds to light.
Refer to the Use and Care Guide for proper operation of the oven
controls.
Adjust Oven Broil Burner Flame (if needed)
Look through oven window to check broil burner for proper flame.
This flame should have a ½" (1.3 cm) long inner cone of bluish-
green, with an outer mantle of dark blue, and should be clean and
soft in character. No yellow tips, blowing or lifting of flame should
be present.
This flame should have a ½" (1.3 cm) long inner cone of bluish-
green, with an outer mantle of dark blue, and should be clean and
soft in character. No yellow tips, blowing or lifting of flame should
be present.
If flame needs to be adjusted:
1. Loosen the lock screw on the air shutter located at the rear of
the broil burner.
2. Adjust the air shutter as needed.
3. Tighten lock screw.
3. Tighten lock screw.
4. Press CANCEL/OFF when finished.
Replace Oven Racks and
Warming Drawer
Replace oven racks in oven cavity. Replace warming drawer.
To Replace Warming Drawer:
1. Insert warming drawer into slide rails on sides of drawer
opening.
2. Lift front of drawer slightly and push firmly to close drawer.
A. Mirror
B. Flame spreader
B. Flame spreader
C. Flame reflection
D. 2 screws
D. 2 screws
A. Air shutter
B. Locking screw
B. Locking screw
A
B
C
D
A
B
A. Lock screw
A
B