Spectrum Brands MI.20xx Manuel D’Utilisation
12
MI.20xx Manual
Hardware information
Introduction
Dynamic Parameters
Dynamic parameters are measured at ± 1 V input range (if no other range is stated) and 50 Ohm termination with the samplerate specified in the table. Measured parameters are avera-
ged 20 times to get typical values. Test signal is a pure sine wave of the specified frequency with > 99% amplitude. SNR and RMS noise parameters may differ depending on the quality
of the used PC. SNR = Signal to Noise Ratio, THD = Total Harmonic Distortion, SFDR = Spurious Free Dynamic Range, SINAD = Signal Noise and Distortion, ENOB = Effective Number
of Bits. For a detailed description please see application note 002.
ged 20 times to get typical values. Test signal is a pure sine wave of the specified frequency with > 99% amplitude. SNR and RMS noise parameters may differ depending on the quality
of the used PC. SNR = Signal to Noise Ratio, THD = Total Harmonic Distortion, SFDR = Spurious Free Dynamic Range, SINAD = Signal Noise and Distortion, ENOB = Effective Number
of Bits. For a detailed description please see application note 002.
Order information
MI.2020
MI.2021
MI.2021
MI.2030
MI.2031
MI.2031
max internal clock
50 MS/s
200 MS/s
max external clock
50 MS/s
100 MS/s
-3 dB bandwidth
> 25 MHz
> 90 MHz
MI.2020
MI.2021
MI.2021
MI.2030
MI.2031
MI.2031
Test - Samplerate
50 MS/s
100 MS/s
Testsignal frequency
1 MHz
1 MHz
SNR (typ)
> 47.5 dB
> 45.9 dB
THD (typ)
< -52.5 dB
< -49.1 dB
SFDR (typ), incl harm.
> 57.0 dB
> 55.5 dB
SINAD (typ)
> 46.0 dB
> 44.2
ENOB (based on SINAD)
> 7.3
> 7.1
Order No
Description
Order No
Description
MI2020
MI.2020 with 16 MSample memory and drivers/SBench 5.x
MI2xxx-32M
Option: 32 MSample memory instead of 16 MSample standard mem
MI2021
MI.2021 with 16 MSample memory and drivers/SBench 5.x
MI2xxx-64M
Option: 64 MSample memory instead of 16 MSample standard mem
MI2030
MI.2030 with 16 MSample memory and drivers/SBench 5.x
MI2xxx-128M
Option: 128 MSample memory instead of 16 MSample standard
mem
mem
MI2031
MI.2031 with 16 MSample memory and drivers/SBench 5.x
MI2xxx-256M
Option: 256 MSample memory instead of 16 MSample standard
mem
mem
MI2xxx-512M
Option: 512 MSample memory instead of 16 MSample standard
mem
mem
MI2xxx-smod
Star Hub: Synchronisation of 2 - 16 boards, one option per system
MI2xxx-up
Additional handling costs for later memory upgrade
MIxxxx.xio
Extra I/O, internal connector: 16 DI/O, 4 Analog out
MIxxxx-xmf
Extra I/O, external connector: 24 DI/O, 4 Analog out, incl. cable
MI2xxx-mr
Option Multiple Recording: Memory segmentation
MI2xxx-time
Timestamp option: Extra memory for trigger time
MI2xxx-gs
Option Gated Sampling: Gate signal controls acquisition
MI2xxx-cs
Synchronisation of 2 - 4 boards, one option per system
Cab-3f-9m-80
Adapter cable: SMB female to BNC male 80 cm
Cab-3f-9m-200
Adapter cable: SMB female to BNC male 200 cm
MI20xx-dl
DASYLab driver for MI.20xx series
Cab-3f-9f-80
Adapter cable: SMB female to BNC female 80 cm
MI20xx-hp
VEE driver for MI.20xx series
Cab-3f-9f-200
Adapter cable: SMB female to BNC female 200 cm
MI20xx-lv
LabVIEW driver for MI.20xx series
MATLAB
MATLAB driver for all MI.xxxx, MC.xxxx and MX.xxxx series.