Visonik Autophonics Home Security System MCT-501 Manuel D’Utilisation

Page de 4
DE3596
1
MCT
MCT
MCT
MCT-501
-501
-501
-501
Advanced Acoustic Sensor / PowerCode Transmitter
Installation Instructions
1
11
1. INTRODUCTION
. INTRODUCTION
. INTRODUCTION
. INTRODUCTION
The MCT-501 combines two modules:
    ••••         The Sentrol Inc. ShatterPro™ acoustic sensor with Pattern
Recognition Technology™ (Protected under U.S. Patent
5,192,931)
    ••••         The Visonic Ltd. MCT-302 PowerCode™ transmitter
Figure 1. General View
Figure 2. Module Identification
1.1 Acoustic Sensor
The acoustic sensor module of the MCT-501 is omni-directional,
providing 360° coverage. Coverage is measured from the sensor
to the point on the glass farthest from the sensor (see Fig. 3). The
sensor can be mounted as close as 1 m (3.3 ft) from the glass.
Figure 3. Typical Range Measurement
When mounted on opposite wall or adjoining walls, the range is
6 m (20 ft) for plate, tempered, laminated and wired glass.
When mounted on the ceiling, the maximum range is 6 m (20 ft)
for plate, tempered, laminated and wired glass
For armor-coated glass, mount the sensor no more than 3.65 m
(12 ft) from the glass.
1.2 PowerCode Transmitter
The acoustic sensor shares its housing with a miniature
transmitter which has a unique 24-bit PowerCode ID, selected in
the factory from over 16 million possible code combinations.  
Upon alarm (glass break detection), a digital message is
transmitted, composed of the PowerCode ID followed by various
status and message-type markers. Alarm and other data are thus
forwarded to the wireless alarm control panel.
Since transmitted messages might collide with transmissions
from other PowerCode transmitters used in the system, a smart
anti-collision transmission sequence is used.
The MCT-501 is protected by a tamper switch that is activated
when the cover is removed. In a tamper situation, a message is
transmitted with the “tamper alert” marker ON.  
A periodic supervision message, distinguished by a specific
marker, is transmitted automatically once in 60 minutes. The
wireless control panel is thus informed, at regular intervals, of the
sensor’s active participation in the system.
A red LED mounted on the transmitter PCB (visible only when the
cover is off) lights whenever alarm or tamper events are reported.
The LED does not light while a supervision message is being
transmitted.
Operating power is obtained from an on-board 3.6 V Lithium
Thionyl Chloride battery. A weak battery will cause a “low battery”
marker to be added to any message transmitted.
2
22
2. SPECIFICATIONS
. SPECIFICATIONS
. SPECIFICATIONS
. SPECIFICATIONS
ACOUSTIC SENSOR SECTION
Microphone
: Omni-directional electret
Alarm Duration: 4 seconds
RF immunity: 20 V/m, 1 MHz to 1000 MHz
Temperature range: -10° to 50°C (14° to 120°F)
Recommended Glass Size:
Minimum: 0.3 x 0.6 m (1 x 2') or larger glass thickness
Plate: 2.4 to 6.4 mm (3/32 to 1/4")
Tempered: 3.2 to 6.4 mm (1/8 to 1/4")
Wired: 6.4 mm (1/4")
Laminated: 3.2 to 6.4 mm (1/8" to 1/4")
POWERCODE TRANSMITTER SECTION
Frequency (MHz):
 315, 404, 418, 433.92 or other frequencies
according to local requirements.
Transmitter's ID Code: 24-bit digital word, over 16 million
combinations, pulse width modulation.
Overall Message Length: 36 bits
Message Repetition: One-shot transmission (default) or once
every 3 minutes.
Supervision: Signaling at 60-minute intervals (U.S. version) or
15 minute interval (UK version)
Response to Tamper Event: Tamper report every 3 minutes
(until the tamper switch is restored).
POWER SUPPLY
Power Source:
 3.6 V Lithium Thionyl Chloride (LiSOCl2) battery,
size 1/2 AA, Tadiran TL-5902 or equivalent.
Nominal Battery Capacity: 1.2 Ah
Current Drain: 24 µA standby, 13 mA on alarm (including LED)
Battery Life (with LED on):
@ 10 transmissions per day: Over 10 years
@ 50 transmissions per day: About 6 years
Battery Supervision: Automatic transmission of battery condition data
as part of any status report.
PHYSICAL
Operating Temperature: 0
°C to 49°C (32°F to 120°F).
Dimensions: 80 x 108 x 43 mm (3.13 x 4.24 x 1.70 in.).
Weight (less battery) : 130 g (4.6 oz)
Housing Material and Color: Flame retardant ABS, white
Standards: Meets FCC Part 15, ETS 300-220 and MPT1349
The 418 & 433.92 MHz models of this device comply with the
European Council Directive EMC 89/336/EEC & 92/31/EEC, and
bear the CE mark and certification.
SMARTHOME™  #73951