Telefunken L32H125A3 Manuel D’Utilisation
English - 38 -
Installing the Batteries to the Remote
1. Lift the cover on the back of the remote upward
gently.
2. Install two AAA batteries. Make sure to match the +
and - ends of the batteries in the battery compartment
(observe the correct polarity.
3.5HSODFHWKHFRYHU
gently.
2. Install two AAA batteries. Make sure to match the +
and - ends of the batteries in the battery compartment
(observe the correct polarity.
3.5HSODFHWKHFRYHU
Connect Power & Antenna/Cable/Satellite
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
SPDIF
VGA
13V dc /18V dc
3
Aerial or Cable
Satellite
DiSEqC
Switch
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC, 50 Hz.
Then the standby LED lights up.
To switch on the TV from standby mode either:
Press the “
Then the standby LED lights up.
To switch on the TV from standby mode either:
Press the “
” button, P+ / P- or a numeric button on
the remote control.
Press the control switch located on the left side of the
TV. The TV will then switch on.
Press the control switch located on the left side of the
TV. The TV will then switch on.
To Switch the TV Off
Press the “
” button on the remote control or press and
hold the control switch on the TV, so the TV will switch
to standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
to standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active. The LED can also blink when you switch on
the TV from standby mode.
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active. The LED can also blink when you switch on
the TV from standby mode.
First Time Installation
:KHQ WXUQHG RQ IRU WKH ¿UVW WLPH WKH ³ODQJXDJH
selection” menu appears. The message “Welcome
please select your language!” is displayed in all
language options listed alphabetically.
selection” menu appears. The message “Welcome
please select your language!” is displayed in all
language options listed alphabetically.
Press the “
” or “
” button to highlight the required
language, press OK button to select. “First Time
Installation” appears. Use “ ” or “ ” button to set
the required country, and press “
Installation” appears. Use “ ” or “ ” button to set
the required country, and press “
” button to select
Search Type (Optional). Use“ ” or “ ” to set the
desired search type. Available search types are Digital
and analog, digital only and analog only. When set,
press “
desired search type. Available search types are Digital
and analog, digital only and analog only. When set,
press “
” to select Teletext Language. Use “ ” or “
” button to set the “Teletext Language” and select “Scan
Encrypted” using “
Encrypted” using “
” or “
” button. You can set Scan
Encrypted as Yes if you want to scan coded stations.
Default PIN code can change depending on the
selected country. If you are asked to enter a PIN code
for viewing a menu option, use one of the following
codes: 4725, 0000 or 1234.
Press OK button on the remote control to continue and
the following message will be displayed on the screen.
selected country. If you are asked to enter a PIN code
for viewing a menu option, use one of the following
codes: 4725, 0000 or 1234.
Press OK button on the remote control to continue and
the following message will be displayed on the screen.