TANDBERG TC3.0 Manuel D’Utilisation
D14635.02—MARCH 2010
40
TANDBERG Codec C90 and Profiles using C90
Administrator guide
Contents
Introduction
Advanced configuration
Password protection
About monitors
Audio matters
Appendices
Contact us
www.tandberg.com
The video outputs at Codec C90
About monitors when you have a
Codec C90
Codec C90
The main monitor
The main monitor can be connected to any of the video outputs
HDMI 1 (the default connector for the main monitor) HDMI 3 (the
default connector for the dual monitor), DVI-I 2 or DVI-I 4.
HDMI 1 (the default connector for the main monitor) HDMI 3 (the
default connector for the dual monitor), DVI-I 2 or DVI-I 4.
Connecting to HDMI 1
The HDMI 1 output is, by default, defined as the main monitor
connector. When you connect the main monitor to this output
the menu and icons (OSD - on screen display) will show on this
monitor.
connector. When you connect the main monitor to this output
the menu and icons (OSD - on screen display) will show on this
monitor.
Connecting to DVI-I 2, DVI-I 4, HDMI 3
When connecting the main monitor to the DVI–I 2, DVI–I 4 or
HDMI 3 output, you must move the OSD to this output.
If you cannot see any menu on screen you must run a key
sequence on the remote control. The menu on screen, icons
and other information (OSD - on screen display) will be moved
to the selected output. At the same time, the resolution will be
set to the default value, which is 1024x768@60Hz for DVI and
1280x720@60Hz for HDMI.
HDMI 3 output, you must move the OSD to this output.
If you cannot see any menu on screen you must run a key
sequence on the remote control. The menu on screen, icons
and other information (OSD - on screen display) will be moved
to the selected output. At the same time, the resolution will be
set to the default value, which is 1024x768@60Hz for DVI and
1280x720@60Hz for HDMI.
Moving the OSD using the remote control
If the main monitor is connected to DVI-I 2 video output you must
run the following shortcut or key sequence on the remote control.
run the following shortcut or key sequence on the remote control.
• Disconnect * # * # 0
x
#
x=1 (HDMI 1); x=2 (DVI–I 2);
x=3 (HDMI 3); x=4 (DVI–I 4)
Example: Set DVI-I 2 as the OSD output.
–
*
–
#
–
*
–
#
–
0
–
2
–
#
Moving the OSD using API commands
You can also set the resolution and the OSD output by setting up
a serial port connection and running API commands. See the API
Guide for the codec for information about API commands.
a serial port connection and running API commands. See the API
Guide for the codec for information about API commands.
Dual monitors
When you want to run a dual monitor setup, connect the second
monitor to video output HDMI 3 on the codec.
monitor to video output HDMI 3 on the codec.
Dual monitor configuration
Go to Advanced settings to set the monitor to dual:
1.
Navigate to Settings > Advanced > Advanced settings > Video
> Output > Monitor and set the
> Output > Monitor and set the
Monitor
to
Dual
.
HDMI 1
(the default connector
for the main monitor)
(the default connector
for the main monitor)
DVI-I 2
HDMI 3
(the default connector
for the dual monitor)
(the default connector
for the dual monitor)
DVI-I 4
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Audio matters
Appendices
About monitors