Quadra-Fire CASTILE-CE-MBK 7068-112 Manuel D’Utilisation

R

August 19, 2011

Page 9

7068-112

1.  First,  make  sure  your  appliance  has  been  properly

installed and that all safety requirements have been met.

Pay particular attention to the fire protection, venting and

thermostat installation instructions.

2.  Double check that the ash drawer and firebox are empty!
3.  Close the front door.
IMPORTANT DETAIL:  The tip of the thermocouple must 

1.  A  thermostat  is  required  for  proper  operation  of  this

appliance. At this time, fill the hopper with pellets, set

the thermostat to its lowest setting. Plug the power cord

into nearby outlet.

2.  The  exhaust  blower  will  stay  on  for  approximately  18

minutes  even  though  the  thermostat  is  not  calling  for

heat. This is normal.

3.  Locate  the  heat  output  control  switch  mounted  on  the

back of the appliance in the upper right corner.

9.1.  Turn it to the “high” setting by pushing the top of

the control switch in and then adjust the thermostat to its

highest setting. Remove the right side panel and the red

call light located to the left of the control box will be on.

Figure 10.1. This indicates the thermostat is calling for

heat.

4.  The fuel feed system and the igniter should now be on.
5.  For your first fire it will be necessary to press the reset

button once approximately 2 minutes after start up and

again in 5 minutes. This will fill the feed system and allow

the appliance to begin dropping pellets. The appliance

will continue to run as long as the thermostat is calling

for heat.

1.  Thermostat Calls For Heat
The  appliance  is  like  most  modern  furnaces;  when  the

thermostat calls for heat, your appliance will

 automatically

light and deliver heat. When the room is up to temperature

and the thermostat is satisfied, the red call light will go off

and the appliance will shut down.
2.  Heat Output Controls
This appliance is equipped with a heat output control switch

that has three settings or burn rates; low, medium and high.

The appliance will turn on and off as the thermostat demands.

When the thermostat calls for heat, the appliance will start

up at the burn rate for which it is set. If the appliance is set

at one of the lower settings, it will run quieter but take longer

to heat up an area than if it were set at a higher burn rate.

Regardless of the burn rate, when the area is warm enough

to satisfy the thermostat, the appliance will shut off.

Fire Hazard.

Keep combustible materials, gasoline

and other flammable vapors and liquids

clear of appliance.

•  Do NOT store flammable materials in the appliance’s

vicinity.

•  DO NOT USE GASOLINE, LANTERN FUEL,

KEROSENE, CHARCOAL LIGHTER FLUID OR

SIMILAR LIQUIDS TO START OR “FRESHEN UP” A

FIRE IN THIS HEATER.

•  DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS

SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL.

•  DO NOT USE CHEMICALS OF FLUIDS TO START

THE FIRE.

•  Keep all such liquids well away from the heater while it

is in use.

•  Combustible materials may ignite.

Heat Output Switch 

Reset Button 

1.  Open the hopper lid and pull the lid towards you. The lid

can now serve as a shelf to support the bag of fuel.

2.  Do not over fill the hopper. The lid must be completely

closed to maintain proper vacuum and for the feed motor

to operate. An error message will appear on the wall

control if the lid is not properly closed.

3.  Remove any sawdust or fuel from the lid gasket after

refilling hopper.

4.  Do not leave any part of the fuel bag on the appliance

after refilling hopper.

5.  Store fuel away from the appliance to maintain proper

safe air clearance to combustibles.