Jura Capresso 65349R3 Manuel D’Utilisation
Please note: There is a gap between the Coffee Nozzle and
the fixed coffee spout. (Fig. 5e) This is necessary to assure
proper coffee flow.
Please note: The Milk Nozzle should always be tightly connected
to the Dial Component (Fig. 5e) and the venting tip needs to
be clean and inserted to assure proper frothing action (Fig. 5a).
the fixed coffee spout. (Fig. 5e) This is necessary to assure
proper coffee flow.
Please note: The Milk Nozzle should always be tightly connected
to the Dial Component (Fig. 5e) and the venting tip needs to
be clean and inserted to assure proper frothing action (Fig. 5a).
• A Thermal Milk Container with lid (Fig. 6a).
• Two stainless steel rods and two flexible hoses (Welcome Pack).
• Two stainless steel rods and two flexible hoses (Welcome Pack).
13. CAPPUCCINO AND LATTE
Make sure the Auto-Cappuccino-System is installed properly
(Fig. 5a – 5e).
Make sure the Auto-Cappuccino-System is installed properly
(Fig. 5a – 5e).
• Fill cold milk into the Thermal Milk Container and assemble the
two stainless steel rods with the lid as shown in Fig. 6 .
• Attach the short flexible hose to the rod and insert the connector
into the Dial Component (Fig. 6a).
Cappuccino: The Dial points to the cup with saucer. Hot milk
and milk froth will be created (Fig. 5f).
and milk froth will be created (Fig. 5f).
Latte: The Dial points to the tall glass. Hot steamed milk with no
or very little froth will be created.
or very little froth will be created.
COFFEE READY
• Place a cappuccino cup underneath the Dual Nozzle System.
The cup should have at least a 8 oz. capacity. Make sure the
dial points to the cappuccino setting (Fig. 5f).
dial points to the cappuccino setting (Fig. 5f).
• Push the Cappuccino Button (Fig. 3).
CAPPUCCINO
The Z5 begins grinding the coffee and at the same time starts
siphoning the cold milk.
siphoning the cold milk.
MILK 15 SEC
.
Hot frothed milk is automatically delivered into your cup.
Frothing stops automatically.
Frothing stops automatically.
3 OZ. NORMAL
. Now the Z5 automatically adds high pressure
brewed coffee and then stops automatically.
COFFEE READY
Tip:
If you use a glass cup you can actually see how much froth
is created and how the coffee goes through the froth and sits
underneath the layer of milk froth. Slightly stir to distribute the
coffee evenly into the hot milk.
underneath the layer of milk froth. Slightly stir to distribute the
coffee evenly into the hot milk.
14. OVERRIDING THE CAPPUCCINO SETTINGS
As with the other buttons you can always override the pre-sets
of the cappuccino button.
Example: Let’s override
As with the other buttons you can always override the pre-sets
of the cappuccino button.
Example: Let’s override
– the coffee strength from NORMAL to XSTRONG,
– the milk frothing time from 15 seconds to 10 seconds,
– the coffee volume from 3 OZ to 2 OZ.
– the milk frothing time from 15 seconds to 10 seconds,
– the coffee volume from 3 OZ to 2 OZ.
COFFEE READY
• Place a cup underneath the Dual Nozzle System.
• Turn the Rotary Dial until the display shows
• Turn the Rotary Dial until the display shows
XSTRONG
.
• Push the Cappuccino button.
• When the display shows
• When the display shows
MILK 15 SEC
, turn the Rotary Dial
until the display shows
10 SEC
.
• When the coffee starts brewing turn the Rotary Dial again until
the display shows
2 OZ.
Please note: You can stop frothing by pushing any of the bever-
age buttons or the Rotary Dial. The Z5 will stop frothing and will
start brewing the coffee. You can stop the coffee brewing in the
same way.
age buttons or the Rotary Dial. The Z5 will stop frothing and will
start brewing the coffee. You can stop the coffee brewing in the
same way.
16.