Honeywell ADEMCO LYNXR Series Guide De Montage

–33–

✻

80 Device Programming Menu Mode

The following explains these prompts in detail. The left two columns identify the prompts and list the
available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than one specified will give unpredictable results.

Powerline Carrier Device
programming

0 = exit mode

1 = enter mode

Entering “1” advances to the next prompt below.
Entering “0” exits mode, upon which this prompt blinks, indicating the
mode is inactive.

Device number

01-08 = device number to be programmed

[✻] = continue

00 = exit Device Programming mode

Enter device numbers as 2-digit entries.

Device action

0 = No response

1 = Close for 2 seconds

2 = Close and Stay Closed

3 = Continuous Pulse on & off (1 sec ON, 1 sec

OFF)

[✻] = continue

[#] = return to previous prompt

Enter the 1-digit action (0-3) for the device being programmed (current
action is displayed).
NOTES:
1. If “3” is entered (pulse), only up to 3 different devices can be pulsed

if one of the devices is a siren/horn (X-10 Powerhouse Security
model SH10A). In addition, the siren/horn cannot be manually
activated using the lights on/lights off keypad commands.

2. If using an X-10 Powerhouse Security SH10A siren:

• you must use device action “3.”

• you must change the device action default to “3” if using default

table 2 or 4

Start event type

0 = Not used

3 = Trouble

1 = Alarm

[✻] = continue

2 = Fault

[#] = return to previous

prompt

Enter the 1-digit event type (0-3) to activate the device being
programmed. A zone list must be used in conjunction with an event. If
a zone type/system operation is to be used instead of an event, enter
“0”.

Start zone list

1-3 = zone list number (to be programmed in

field ✻81)

0 = zone list not used for this device

[✻] = continue

[#] = return to previous prompt

If a zone list will be used to start the device action, enter the zone list
number at this prompt.

Start zone type

01-58 = zone type to start this device action

(select only those that are applicable)

00 = zone type not used for this device

[✻] = continue

[#] = return to previous prompt

If a zone type or system operation will be used to start the device
action, enter the appropriate 2-digit code for the device being
programmed (see table that follows).

Choices for zone types

00 = Not Used

04 = Interior Follower

08 = 24 Hr Aux

01 = Entry/Exit #1

05 = Trouble Day/Alarm Night 09 = Fire

02 = Entry/Exit #2

06 = 24 Hr Silent

10 = Interior w/Delay

03 = Perimeter

07 = 24 Hr Audible

24 = Silent Burglary

Choices for system operation

20 = Arming–Stay

33 = Any Alarm (except zt 08) 42 = Sys. Batt. Low

21 = Arming–Away

36 = At Bell Timeout**

43 = Comm. Failure

22 = Disarm. (Code + OFF) 38 = Chime

52 = Kissoff

31 = End of Exit Time 39 = Any Fire Alarm

58 = Duress

32 = Start of Entry Time

40 = Bypassing

** Or at Disarming (which ever occurs earlier)

Note: If an X-10 device has been programmed to ZT05 or ZT07 and *55

has been enabled, the device response will be dependent upon the
selection made in *55 Field "Ln".

Stop zone list

1-3 = zone list to stop this device action

0 = zone list not used

[✻] = continue

[#] = return to previous prompt

If a zone list will be used to STOP, or restore, the device action, enter
the zone list number 1, 2, or 3 (to be programmed in

✻

81 mode). If not

used, enter “0”.

Stop zone type

01-58 = zone type to start this device action

(select only those that are applicable)

00 = zone type not used for this device

[✻] = continue

[#] = return to previous prompt

If a zone type or system operation will be used to STOP the device
action, enter the appropriate 2-digit code (see the "ZT" choices listed
above). If not, enter 00.
The display then returns to the DEVICE NUMBER prompt (A) so that
you can enter the next device number to be programmed, or enter [0][0]
to end device programming.