Grandstream Networks GXV300X Manuel D’Utilisation
Grandstream Networks, Inc.
GXV300x User Manual
Page 28 of 54
Firmware 1.2.3.7
Updated: 12/2010
Video Frame
Skipping
Skipping
Skipping the bad video frame received
Default is No.
Default is No.
Sharpening Filter Sharpening filter for incoming video. Default value is 5
Brightening Filter Brightening filter for incoming video. Default value is 5
Tone Remapping
Filter
Filter
Default value is 32. It can be used to improve video quality under low light conditions by equalizing
(remapping) colors/tones.
Tone Remapping Filter can also be adjusted after video conversation is established.
(remapping) colors/tones.
Tone Remapping Filter can also be adjusted after video conversation is established.
- Use MWI button
to toggle between VOLUME, BIT RATE, and Tone Remapping Filter
mode.
- After choosing the feature, use UP and DOWN arrow to adjust.
- After choosing the feature, use UP and DOWN arrow to adjust.
Packetization-
mode
mode
Default is 0.
Enable Video
Surveillance
Surveillance
Default is No. If configured to YES, the video phone can be turned to a video surveillance camera
after the phone rebooted.
after the phone rebooted.
Surveillance
RTSP port
RTSP port
This is the port for the video surveillance camera data stream.
Default is 554.
Default is 554.
Streaming RTSP
Server
Server
This is for the URI of the streaming RTSP server.
GXV300x can also be a remote surveillance monitor for another GXV300x phone used as surveil-
lance camera or other supported IP Camera or video source. For such application, both devices
(Server and Monitor) have to be in the same LAN or VPN.
GXV300x can also be a remote surveillance monitor for another GXV300x phone used as surveil-
lance camera or other supported IP Camera or video source. For such application, both devices
(Server and Monitor) have to be in the same LAN or VPN.
Streaming RTSP
User ID
User ID
The user ID used to connect to RTSP server.
To act as remote surveillance monitor, the GXV300x has to give the RTSP server authorized User
ID in order to fetch the RTSP streaming packets.
To act as remote surveillance monitor, the GXV300x has to give the RTSP server authorized User
ID in order to fetch the RTSP streaming packets.
Streaming RTSP
Password
Password
The password used to connect to RTSP server.
To act as remote surveillance monitor, the GXV300x has to give the server authorized Password
to match the credentials in order to fetch the RTSP streaming packets.
To act as remote surveillance monitor, the GXV300x has to give the server authorized Password
to match the credentials in order to fetch the RTSP streaming packets.
Layer 3 QoS
This field defines the layer 3 QoS parameter.
It is the value used for IP Precedence or Diff-Serv or MPLS. Default value is 0.
It is the value used for IP Precedence or Diff-Serv or MPLS. Default value is 0.
Layer 2 QoS
This contains the value used for layer 2 VLAN tag (802.1q and 802.1p). Default setting is blank.
No Key Entry
Timeout
Timeout
Default is 4 seconds. User can press SEND key (or # key if configured) to overwrite the 4 seconds
value to speed up dialing
value to speed up dialing
Use # as
Dial Key
Dial Key
This parameter allows users to configure the “#” key as the “Send” (or “Dial”) key.
If set to “Yes”, the “#” key will immediately send the call. In this case, this key is essentially
equivalent to the “(Re)Dial” key. If set to “No”, the “#” key is included as part of the dial string.
If set to “Yes”, the “#” key will immediately send the call. In this case, this key is essentially
equivalent to the “(Re)Dial” key. If set to “No”, the “#” key is included as part of the dial string.
Local RTP port
This parameter defines the local RTP-RTCP port pair used to listen and transmit. It is the base
RTP port for channel 0. When configured, for audio, channel 0 will use this port _value for RTP
and the port_value+1 for its RTCP; channel 1 will use port_value+4 for RTP and port_value+5 for
its RTCP. For video, channel 0 will use port_value+2 for RTP and port_value+3 for its RTCP;
channel 1 will use port_value+6 for RTP and port_value+7 for RTCP. The default value is 5004
RTP port for channel 0. When configured, for audio, channel 0 will use this port _value for RTP
and the port_value+1 for its RTCP; channel 1 will use port_value+4 for RTP and port_value+5 for
its RTCP. For video, channel 0 will use port_value+2 for RTP and port_value+3 for its RTCP;
channel 1 will use port_value+6 for RTP and port_value+7 for RTCP. The default value is 5004