Audiovox TFT3500 Fascicule
Headphones
For private listening,you can connect optional mono headphones
to the 3.5mm EAR jack. This automatically mutes the built-in
speaker.
Set the VOLUME to the lowest setting before you plug in the
headphones. After the headphones are connected, adjust the
volume to a comfortable level.
to the 3.5mm EAR jack. This automatically mutes the built-in
speaker.
Set the VOLUME to the lowest setting before you plug in the
headphones. After the headphones are connected, adjust the
volume to a comfortable level.
TV Stand
The TV stand (located on the rear of this unit) gives you the
convenience of placing the TV on a flat surface for easy viewing.
Pull the stand slowly until it locks into place. Do not pull the stand
beyond the lock position. When finished using the stand, snap it
back into place.
convenience of placing the TV on a flat surface for easy viewing.
Pull the stand slowly until it locks into place. Do not pull the stand
beyond the lock position. When finished using the stand, snap it
back into place.
Troubleshooting
Problem
Solution
No picture and/or
Check the battery polarity.
no sound
If using an AC power adaptor, make
sure it is the correct voltage(6VDC 500mA), the
correct polarity +/-, and connected
properly.
Recharge
Recharge
the
batteries.
Change
the
batteries.
Picture,but no sound
Make sure headphones are
disconnected.
Adjust
Adjust
VOLUME
control.
If using an external video source, check
all
connections.
Sound, but no picture
Check the Batteries. Batteries may
need
replacement
or
charging
Adjust
the
antenna.
Adjust
the
brightness.
If using a video source, check all
connections.
No color
Adjust the antenna.
Re-adjust
the
tuning.
Picture not clear
Extend the antenna fully and adjust the
angle
and
direction.
Re-adjust
the
tuning.
Batteries may need charging or
replacement
if
alkaline.
Move the TV away from devices which
may
cause
interference.
Watching TV
Extend the antenna.
Set the power switch to VHF (channels 2-13) or UHF (channels
14-69). The TV starts scanning and stops at the first active signal.
Press the tuning +/- buttons to change channels. The channel
indicator(red for VHF and green for UHF) aligns with the selected
channel number on bottom of the screen.
Adjust the volume to a desired level.
Adjust the brightness if the image is too light or dark
Set the power switch to VHF (channels 2-13) or UHF (channels
14-69). The TV starts scanning and stops at the first active signal.
Press the tuning +/- buttons to change channels. The channel
indicator(red for VHF and green for UHF) aligns with the selected
channel number on bottom of the screen.
Adjust the volume to a desired level.
Adjust the brightness if the image is too light or dark
Note: If reception is poor,adjust the length or angle of the antenna. If
inside a metal or concrete building, moving closer to a window may
improve the reception.
inside a metal or concrete building, moving closer to a window may
improve the reception.
Audio/Video in
With a compatible audio/video adapter(not included), your TV can
receive signals from a video device, such as a camcorder or VCR.
receive signals from a video device, such as a camcorder or VCR.
Conncet the RCA plugs into the video and left/mono jacks of the
video device. The yellow plug is for video, the white plug is for
audio.
Plug the 3.5mm plug into the A/V IN jack on the side of the TV.
Turn on theTV.
video device. The yellow plug is for video, the white plug is for
audio.
Plug the 3.5mm plug into the A/V IN jack on the side of the TV.
Turn on theTV.
Note:Plugging in this jack switches the TV from TV mode to Video
mode. Uplugging this jack will return the TV to TV mode.
mode. Uplugging this jack will return the TV to TV mode.
Powering UP continued
AA NIHM BATTERIES:
Press the battery cover release tab and gently lift the battery
cover open.
Set the recharge switch located inside the battery
compartment to the "ON" position
Insert the four NiMH batteries observing the polarity
symbols(+and -) shown inside the battery compartment.
Close battery cover.
Connect the AC adaptor/charger to the DC input connector.
Charge the batteries for at least 2 hours. The charge indicator
will be illuminated while the batteries are recharging.
Press the battery cover release tab and gently lift the battery
cover open.
Set the recharge switch located inside the battery
compartment to the "ON" position
Insert the four NiMH batteries observing the polarity
symbols(+and -) shown inside the battery compartment.
Close battery cover.
Connect the AC adaptor/charger to the DC input connector.
Charge the batteries for at least 2 hours. The charge indicator
will be illuminated while the batteries are recharging.
If using the AC adaptor with Alkaline batteries
installed in the TV, you MUST switch the
Recharge switch to "OFF" position.Failure to
do so can result in personal injury or damage.
installed in the TV, you MUST switch the
Recharge switch to "OFF" position.Failure to
do so can result in personal injury or damage.
AC ADAPTER/CHARGER:
A 6V DC 500mA AC adaptor/Charger can also
be used to power the TV in your home or office. Simply
connect the AC adaptor/Charger to the DC Input on your TV.
The rechareable NIHM batteries will be recharged while you are
watching the TV, though the recharge time will be increased.
For best results, it is recommended that you recharge the
batteries with the unit off.
be used to power the TV in your home or office. Simply
connect the AC adaptor/Charger to the DC Input on your TV.
The rechareable NIHM batteries will be recharged while you are
watching the TV, though the recharge time will be increased.
For best results, it is recommended that you recharge the
batteries with the unit off.