Dacor Electric Grill OBSB162 Manuel D’Utilisation

19

Care and Cleaning

Cleaning the Optional Side 

Burners

Cover the side burners with the included stainless 

• 

steel burner cover when they are not in use and cool. 

Doing so will protect them and help keep them clean.
the igniter will not work properly if the burner cap, 

• 

burner head, burner base or the igniter itself are 

not clean. A dirty or wet igniter may not spark at 

all. Keep the igniters clean and dry to reduce this 

problem and avoid unnecessary service calls.

remove the grate and disassemble the side burners 

1. 

underneath for cleaning as shown. After disassem-

bling them, check for any dirt or grime deposited on 

the individual parts, including the igniters.
Brush completely around 

2. 

the igniter, including over 

and under the edge of the 

metal top and porcelain 

base. A stiff toothbrush is 

ideal for this task. Use care 

while cleaning because 

the porcelain igniter base 

is fragile and can crack or  

break. Do not use water to 

clean the igniters. If neces-

sary, use a small amount 

of rubbing alcohol to help 

dissolve grime.
examine the burner caps. 

3. 

remove anything stuck in 

the holes with a straight-

ened paper clip, wire or needle. Be careful not to 

scratch or damage it. Do not distort the shape of the 

holes.
Clean the burner cap and head with window cleaner 

4. 

or rubbing alcohol. Use a cleaning brush with plastic 

bristles or a firm tooth brush. When done, rinse the 

parts well with clean water. Dry the parts thoroughly 

before re-assembling them.
Test the burners after re-assembly. If the flame is 

5. 

uneven, be sure that the brass burner cap and the 

burner head are properly positioned. Check for any 

dirt or grime in the burner cap. If erratic clicking is 

still present, make sure the igniter is completely dry. 

If the unit still exhibits problems after drying, call your 

local Dacor

 

 Authorized Service Agent.

Cleaning the Exterior

Knobs and Trim Rings

Do not soak the knobs in water or put them in

• 

 a 

dishwasher.
Do not remove the trim rings from the 

• 

appliance. 

Clean only the outside edges of the trim rings. If you 

get moisture inside the trim rings, damage to the 

electronic components can occur.
Do not expose the knobs to hot objects, intense heat 

• 

or direct flame. Damage may result. 

Wash the knobs regularly with a solution of warm 

• 

soapy water. Dacor recommends hand dishwashing 

liquid.
turn the knobs to the off position to remove them for 

• 

cleaning or replacement.
Grasp each knob and pull straight back, off of the 

• 

valve shaft.
Clean the outside edges of the trim rings while the 

• 

knobs are removed. Wipe them with a soft damp rag.
to replace the knobs, 

• 

align the “D-shaped” 

opening on the back 

of the knob with 

the end of the valve 

shaft. Carefully push 

the knob on until it 

stops.

Exterior Stainless Steel Surfaces, Chrome 

and Other Metal Surfaces

Always wipe stainless steel (silver colored) surfaces 

• 

with the grain. 
to prevent scratching, do not use abrasive cleaners 

• 

or scrubbers on stainless steel or other metal 

surfaces.

Clean the exterior stainless steel surfaces with the 

• 

Dacor Stainless Steel Cleaner included with your 

appliance. Use it according to the directions on the 

package. See the Parts and Accessories section to 

order additional cleaner.
You may also use a mild solution of detergent and 

• 

warm water on stainless steel surfaces. rinse and dry 

with a soft, lint-free cloth.
to clean other metal surfaces, use a soft clot

• 

h with a 

mild solution of detergent and warm water. rinse and 

dry with a soft, lint-free cloth.

Burner cap

Burner head

Burner base

Igniter