Benq PB9200 Manuel D’Utilisation
Power ON/OFF
14
Power ON/OFF
WARNING
•
When the power is ON, a strong light is emitted. Do not look into the lens or vents of
the projector.
the projector.
NOTE
•
Turn the power on/off in right order. Please power on the projector before the
connected devices. Power off the projector after the connected devices.
connected devices. Power off the projector after the connected devices.
Turning On The Power
1.
Remove the lens cap.
2.
Set the power switch to [ | ] (ON). The
STANDBY/ON indicator will light to
solid orange.
STANDBY/ON indicator will light to
solid orange.
3.
Press the STANDBY/ON button. The
projector lamp will light up and the
STANDBY/ON indicator will begin
blinking green. When the power is
completely on, the indicator will stop
blinking and light green.
projector lamp will light up and the
STANDBY/ON indicator will begin
blinking green. When the power is
completely on, the indicator will stop
blinking and light green.
4.
Use the LENS SHIFT buttons to shift
the picture upward or downward.
the picture upward or downward.
5.
Select an input signal according to the
section “Selecting An Input Signal” of
the following page.
section “Selecting An Input Signal” of
the following page.
Turning Off The Power
1.
Press the STANDBY/ON button. The
message “Power off?” will appear on the
screen for approximately 5 seconds.
Attach the lens cap.
message “Power off?” will appear on the
screen for approximately 5 seconds.
Attach the lens cap.
2.
Press the STANDBY/ON button again
while “Power off?” the message is visi-
ble. The projector lamp will go off, and
the STANDBY/ON indicator will begin
blanking orange. Then the STANDBY/
ON indicator will stop blinking and
light to solid orange when the lamp
cooling is complete.
while “Power off?” the message is visi-
ble. The projector lamp will go off, and
the STANDBY/ON indicator will begin
blanking orange. Then the STANDBY/
ON indicator will stop blinking and
light to solid orange when the lamp
cooling is complete.
3.
Switch the power switch to [O] (OFF). The STANDBY/ON indicator will go off.
4.
Attached the lens cap.
Power switch (ON position)
LENS SHIFT buttons
INTER
INPUT
M1-D
RGB
BNG
S-VIDEO
STANDBY/ON
TEMP
VIDEO
COMPONENT
LAMP
KEYSTONE
SEARCH
RESET
MENU
FOCUS
LENS SHIFT
ZOOM
VIDEO
R-AUDIO IN-L
S-VIDEO
BNC
RGB
AUDIO IN1
AUDIO IN2
RGB OUT
AUDIO OUT
REMOTE CONTROL
R/CR/PR
G/Y
B/CB/PB
H
V
Y
CONTROL
NETWORK
CR/PR Ca/Pa
STANDBY/ON
VIDEO
LASER INDICATOR
RGB
BLANK
ASPECT
LASER
LENS SHIFT
+
–
–
–
+
+
FOCUS
ZOOM
STANDBY/ON
LENS SHIFT
STANDBY/ON
VIDEO
LASER INDICATOR
RGB
BLANK
ASPECT
LASER
LENS SHIFT
+
–
–
–
+
+
FOCUS
ZOOM
INTER
INPUT
M1-D
RGB
BNG
S-VIDEO
STANDBY/ON
TEMP
VIDEO
COMPONENT
LAMP
KEYSTONE
SEARCH
RESET
MENU
FOCUS
LENS SHIFT
ZOOM
VIDEO
R-AUDIO IN-L
S-VIDEO
BNC
RGB
AUDIO IN1
AUDIO IN2
RGB OUT
AUDIO OUT
REMOTE CONTROL
R/CR/PR
G/Y
B/CB/PB
H
V
Y
CONTROL
NETWORK
CR/PR Ca/Pa
STANDBY/ON button / indicator
STANDBY/ON
STANDBY/
ON button
Power switch (OFF position)
INTER
INPUT
M1-D
RGB
BNG
S-VIDEO
STANDBY/ON
TEMP
VIDEO
COMPONENT
LAMP
KEYSTONE
SEARCH
RESET
MENU
FOCUS
LENS SHIFT
ZOOM
VIDEO
R-AUDIO IN-L
S-VIDEO
BNC
RGB
AUDIO IN1
AUDIO IN2
RGB OUT
AUDIO OUT
REMOTE CONTROL
R/CR/PR
G/Y
B/CB/PB
H
V
Y
CONTROL
NETWORK
CR/PR Ca/Pa
STANDBY/ON
VIDEO
LASER INDICATOR
RGB
BLANK
ASPECT
LASER
LENS SHIFT
+
–
–
–
+
+
FOCUS
ZOOM
STANDBY/ON
STANDBY/ON button / indicator
STANDBY/ON
STANDBY/
ON button
PB9200-e.book Page 14 Thursday, May 27, 2004 2:15 PM