Behringer U-CONTROL UMX49 Manuel D’Utilisation

11

U-CONTROL UMX49/UMX61

4. OPERATION

The LSB part describes each of the 128 MSBs in another 128

individual stages. Both are individually numbered from 0 to 127.

The enormous value range of a total of 128 x 128 = 16.384

different values is therefore available to you via the BANK
SELECT command. This theoretically means that you could use
external devices which support the same amount of different
banks.

If you consider that each of these banks again contains another

128 individual programs, you will receive the unbelievably large
number of 2,097,152 different options to organize these
programs.

1)

Press the ASSIGN push-button and hold it down.

2)

Press one of the 16 channel keys 

 through

, or press the 

 key.

3)

Release the ASSIGN push-button.

4)

Press the 

 key. Then press the number keys in

sequence until you have completely entered the desired
BANK MSB number. Only value entries between 0 and
127 are possible. Greater values are ignored by the device.

The BANK MSB has now been defined.

Example:
- Press  

 and 

 if you have decided on MSB

14, for example.
- Press 

,  

 and 

 if you would like to

select MSB 107.

5)

Now define the BANK LSB by pressing the 

 key.

Then enter the number value of the BANK LSB with the
already familiar procedure (see step 4). The same entry
rules apply as for the BANK MSB.

You have defined the bank in which the desired program
will be called up in steps 4 and 5. Now all you have to
define is the program itself:

6)

Press the 

 key and then press the number keys

in sequence until you have completely entered the desired
program number. Only entries between 0 and 127 are
possible, greater values are ignored by the device. Ready!

7)

Finally, press the 

 key. In order to discard your

assignments, please press the 

 key or press the

ASSIGN push-button again. The ASSIGN LED will go off
in all 3 cases.

Example:
You want to select preset No. 49 in bank 25 of an external
device on channel 14 via the UMX. Only the LSB will be used to
describe the bank, since the bank number remains less than
128. The MSB in this case equals 0.

1)

Press and hold the ASSIGN push-button.

2)

Press the channel key 

.

3)

Press and hold the ASSIGN push-button.

2)

Press the channel key.

4)

Then, press the 

 key or the 

 key.

5)

Press 

 key and then describe bank 25 with push-

buttons 

 and 

.

6)

Define the program: Press the 

 key and then the

 and 

 keys for program 49.

7)

Press the 

 key.

1)

Press the ASSIGN push-button and hold it down.

2)

Select the OCTAVE SHIFT push-button which you want to
assign to the program change function.

3)

Release the ASSIGN push-button again.

4)

Defined the channel by which the program change will be
transmitted. Press one of the 16 channel keys 
through 

 on the keyboard.

5)

Press the 

 key. Then press the number keys on

the keyboard in sequence until you have completely entered
the desired preset number. Only value entries between 0
and 127 are possible. Greater values are ignored by the
device.

6)

Finally, press the 

 key. In order to discard your

assignments, please select the 

 key or press the

ASSIGN push-button again. The ASSIGN LED will go off in
all 3 cases.



The OCTAVE SHIFT push-buttons of the device are in their initial

state every time the UMX is switched on (refer to table 3.1).

Further special functions can be assigned to both push-buttons

in the ASSIGN mode in addition to the already covered functions
regarding direct program change and octave transposition:

a)

Transposition in individual semitone steps

b)

Sequential scrolling in program libraries

c )

Optional controller functions





1)

Press the ASSIGN push-button and hold it down.

2)

Press the 

 key.

3)

Release the ASSIGN push-button.

4)

Finally, press the 

 key. In order to discard your

assignments, please press the 

 key or press the

ASSIGN push-button again. The ASSIGN LED will go off
in all 3 cases.

Pressing the right hand one of the two push-buttons causes a

shift by one semitone upward pressing the left hand one leads to
a shift by one semitone downward. Pressing both push-buttons
cancels all transpositions.



DATA-MANFULL_UMX49_ENG_Rev_A.pmd

12.01.2006, 20:37

11