Wybron NET IT PS600 Manuel D’Utilisation
16
Net-IT Operation
Net-IT sample screens in Art-Net mode.
The front panel display shows the current settings. Changing most of the settings is
done through the Net-IT web page. To get to the web page read the IP address off the
display, open a browser on your PC or Mac, and enter the IP address in the top line of
the browser. See the Quick Start Guide near the beginning of this manual for
instructions on how to connect the Net-IT to your computer.
Setting a user defined IP address
On the web page enter a new IP address and click on Submit. The Net-IT will re-boot
and use the new address. The web page should display again after several seconds. If
it does not then change the IP address of your computer to be on the new Net-IT
subnet.
Setting DHCP IP
To configure the Net-IT to automatically get an IP address from a DHCP server on your
network, on the web page enter 0.0.0.0 for the IP address and click on Submit. The Net-
IT will re-boot and DHCP. To get back to the web page read the new IP address off the
display and enter it into your web browser.
Setting the DMX Network Protocol
On the web page you may select the network protocol from a pulldown option, then click
on Submit. If you had previously assigned DMX universes to the Net-IT they will be
reset to default values. When the Net-IT is configured for Art-Net and connected on a
network to an Art-Net controller, the controller will automatically discover the Net-IT.
There is no discovery operation performed by an E1.31 network DMX source. The
source simply sends the DMX over the network to whoever is listening.
The front panel display shows the current settings. Changing most of the settings is
done through the Net-IT web page. To get to the web page read the IP address off the
display, open a browser on your PC or Mac, and enter the IP address in the top line of
the browser. See the Quick Start Guide near the beginning of this manual for
instructions on how to connect the Net-IT to your computer.
Setting a user defined IP address
On the web page enter a new IP address and click on Submit. The Net-IT will re-boot
and use the new address. The web page should display again after several seconds. If
it does not then change the IP address of your computer to be on the new Net-IT
subnet.
Setting DHCP IP
To configure the Net-IT to automatically get an IP address from a DHCP server on your
network, on the web page enter 0.0.0.0 for the IP address and click on Submit. The Net-
IT will re-boot and DHCP. To get back to the web page read the new IP address off the
display and enter it into your web browser.
Setting the DMX Network Protocol
On the web page you may select the network protocol from a pulldown option, then click
on Submit. If you had previously assigned DMX universes to the Net-IT they will be
reset to default values. When the Net-IT is configured for Art-Net and connected on a
network to an Art-Net controller, the controller will automatically discover the Net-IT.
There is no discovery operation performed by an E1.31 network DMX source. The
source simply sends the DMX over the network to whoever is listening.
ArtNet Name
Wybron Net-IT
InfoTrace Name
ArtNet Gtway
Infotrace connected: Yes
Network Protocol: Art-Net
Wybron Net-IT
InfoTrace Name
ArtNet Gtway
Infotrace connected: Yes
Network Protocol: Art-Net
ArtNet Parameters
Subnet: 0
Port A Universe: 0
Port B Universe: 1
Port A: Output
Port B: Output
Port A Universe: 0
Port B Universe: 1
Port A: Output
Port B: Output
Software Ver: 1.02
IP: 10.13.56.123
Subnet Mask:
255.0.0.0
MAC:
00:03:f4:03:0d:68
Artnet Port: 0x1936
IP: 10.13.56.123
Subnet Mask:
255.0.0.0
MAC:
00:03:f4:03:0d:68
Artnet Port: 0x1936