Alpine CDA-105RI Manuel D’Utilisation
28
-EN
When Blackout mode is turned on, all display indications on this unit
will turn off to reduce power consumption. This additional power
enhances the sound quality.
will turn off to reduce power consumption. This additional power
enhances the sound quality.
B.OUT OFF (Initial setting)
B.OUT ON
• When Blackout mode is set to ON, after 5 seconds, all displays on the
unit will turn off.
• If any button on the unit is pressed during the blackout mode, the
function will be displayed for 5 seconds to show the operation before
returning to Blackout mode.
returning to Blackout mode.
The setting of PARAMETER EQ/GRAPHIC EQ, T.CORRECTION
and CROSSOVER can be adjusted in this mode.
and CROSSOVER can be adjusted in this mode.
Adjusting the Parametric Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ MODE to PARAMETER EQ. For details, refer to
“Setting EQ mode” (page 27).
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ MODE to PARAMETER EQ. For details, refer to
“Setting EQ mode” (page 27).
1
After selecting PARAMETER
EQ from the SOUND
ADJUST mode, press BAND/TA to select the band
to be adjusted.
to be adjusted.
B 1
B 2
B 3
B 4
B 5
B 1
2
Press
or
to select frequency bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
20 Hz to 20 kHz (in 1/3 octave steps)
Band-1: 20 Hz~80 Hz (63 Hz)
Band-2: 50 Hz~200 Hz (150 Hz)
Band-3: 125 Hz~3.2 kHz (400 Hz)
Band-4: 315 Hz~8 kHz (1 kHz)
Band-5: 800 Hz~20 kHz (2.5 kHz)
3
Turn the Rotary encoder to adjust the level.
Adjustable level: -6 to +6 dB
4
Press SOURCE/
to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
5
To adjust another band, repeat steps 4 to 7 and
adjust all bands.
adjust all bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the PARAMETER EQ, you should consider the
• While adjusting the PARAMETER EQ, you should consider the
frequency response of the connected speakers.
Adjusting the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ MODE to GRAPHIC EQ. For details, refer to “Setting EQ
mode” (page 27).
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ MODE to GRAPHIC EQ. For details, refer to “Setting EQ
mode” (page 27).
1
After selecting GRAPHIC EQ from the SOUND
ADJUST mode, press BAND/TA to select the band
to be adjusted.
ADJUST mode, press BAND/TA to select the band
to be adjusted.
B 1
B 2
B 3
B 4
B 5
B 6
B 7
B 1
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
2
Turn the Rotary encoder to adjust the level.
Adjustable output level: -6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and
then adjust all bands.
then adjust all bands.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 30).
Correction” (page 30).
1
After selecting T.CORRECTION from the SOUND
ADJUST mode, press BAND/TA to select a speaker
to be adjusted.
ADJUST mode, press BAND/TA to select a speaker
to be adjusted.
2.2ch (3WAY) System
4.2ch (FRONT/REAR/SUBW.) System
2
Turn the Rotary encoder to adjust the distance
correction value (0.0 to 336.6cm).
correction value (0.0 to 336.6cm).
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 30.
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
listening position at the same time as the sound of other
speakers.
Adjusting the Crossover Settings
Before performing the following procedures, refer to “About the
Crossover” (page 31).
Crossover” (page 31).
2.2ch (3WAY) System
1
After selecting CROSSOVER from the SOUND
ADJUST mode, press BAND/TA to select the band
to be adjusted.
ADJUST mode, press BAND/TA to select the band
to be adjusted.
2.2ch (3WAY) System / NORMAL (L=R)
Setting items:
LOW / M-L / M-H / HIGH
2.2ch (3WAY) System / INDIVIDUAL (L/R)
Setting items:
L-L / L-R / ML-L / ML-R / MH-L / MH-R / H-L / H-R
2
Press
or
to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
Setting items:
LOW / M-L
20 Hz~200 Hz
M-H
20 Hz~20 kHz
HIGH
(1 kHz~20 kHz)
*
1
/(20 Hz~20 kHz)
*
2
*
1
When MAKER’S is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW SETUP)” (page 27).
the High Range Speaker (TW SETUP)” (page 27).
*
2
When USER’S is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW SETUP)” (page 27).
the High Range Speaker (TW SETUP)” (page 27).
Blackout Mode On and Off
Sound Field Adjustment (SOUND ADJUST)
F-L (Initial setting)
F-R
R-L
R-R
(Mid-L)
(Mid-R) (High-L ) (High-R)
SW-L
SW-R
F-L
(Mid-L)
F-L (Initial setting)
F-R
R-L
R-R
(Front-L)
(Front-R) (Rear-L) (Rear-R)
SW-L
SW-R
F-L
(Front-L)