Welch Allyn Medical Diagnostic Equipment 2380 Manuel D’Utilisation

As a general overview of the programming menu. The programming menu consists of two basic components as
shown below.

Each menu page represents one section of the programming menu. Use individual menu pages in combination with
the bar code chart on the back page foldout to program the decoder.

The bar codes on this chart are assigned to a ROMAN NUMERAL, DIGIT, LETTER OR YES/NO symbol. These bar
codes correspond to the symbols in shaded areas on the menu pages and are scanned in various combinations to
enter programming sequences to the decoder. Bar codes on this page are meaningless unless an ENTER bar code
from one of the menu pages is first scanned.  When an ENTER bar code is scanned, the bar code chart becomes
specific to that menu page and remains so until the EXIT bar code is scanned or another menu page is selected.

USE THIS PAGE – is a summary of the programming options (parameters) of each menu page.

DEFAULT – Most menu pages have a DEFAULT bar code which allows the user to independently default menu
pages to astericked (*) values without affecting, in any way, the rest of the programming menu. Default values can be
easily selected from the desired menu pages by scanning the bar code sequence ENTER, DEFAULT, EXIT.
Individual defaults for a specific selection can be made by scanning ENTER, ROMAN NUMERAL, DEFAULT, EXIT.

ENTER – Each menu page has its own unique ENTER bar code; scan this bar code to activate desired menu page.

EXIT – To move from one menu page to another, scan the EXIT bar code. This bar code must be scanned to end
programming selection on each menu page before beginning to program on a different menu page.

SELECTIONS/VARIABLES – Lists all of the options available on each menu page. Following each option are
symbols in shaded areas. These symbols correspond to bar codes on the adjoining bar code chart.

The page facing the menu is often used to supplement or clarify the material presented on the front of each menu
page. The information and examples found here are specific to the individual menu page and contain, in some cases,
charts and diagrams that must be used in order to determine the correct programming sequence.

To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol.
To enable or disable listed code selections.

UPC

Version A
Version D(2)
Version E0

*Yes/No

No*

*Yes/No

ID = c
(HEX 63)

Version E1
Check Digit Xmit
Number System Xmit
Version E Expand

A

B
C
D
E
F

*Yes/No

*Yes/No
Yes/No*

*Yes/No

(2) UPC Version D is not supported at this time.

EAN

EAN/JAN 13
EAN/JAN 8
Check Digit Xmit

*Yes/No
*Yes/No

ID = d
(HEX 64)

*Yes/No

2–Digit Addenda
5–Digit Addenda

A
B
C
D
E

*Yes/No
*Yes/No

UPC & EAN

Enable

Yes/No*



MSI

Enable
Minimum Length

Maximum Length

Yes/No*

*04–Max
Min–48*

ID = g
(HEX 67)



Plessey

Enable

Minimum Length

Maximum Length

*04–Max

Yes/No*

Min–48*

ID = n
(HEX 6E)

G

Addenda Req’d.

2–Digit Addenda
5–Digit Addenda

H

*Yes/No
*Yes/No

I

ENTER

DEFAULT

EXIT

A
B

A
B

(1) * Designates DEFAULT selections.

In combination with the adjoining menu pages to program the unit.

The bar codes on this page correspond to symbols in shaded areas on adjoining menu pages. SCAN these bar codes in the sequence indicated on
menu page to program desired selections and variables.

I

II

III

IV

V

VI

VII

VIII

IX

X

XI

XII

XIII

XIV

XV

XVI

XVII

XVIII

XIX

XX

A

B

C

D

E

F

G

H

I

J

0 (YES)

1 (NO)

2

3

4

5

6

7

8

9

ESCAPE

DEFAULT

EXIT

ROMAN NUMERALS

LETTERS

DIGITS

OTHERS

NOTES – are provided to call out any unusual situations and/or refer you to necessary information or examples
elsewhere in the menu or manual.

Use this bar code to cancel current programming sequence.  All parameters remain as they were.  Scan ESCAPE.