Kramer Electronics Computer Hardware VS-1616D Fascicule
VS-1616D HDMI I/O Card Installation Sheet
(
: 2900-0007278
)
P/N
REV 1
Kramer Electronics Ltd.
VS-1616D HDMI I/O Card Installation Sheet
5. Holding the card by the upper and lower handle, align the
card with the plastic guide rails.
card with the plastic guide rails.
6. Slide the card into the chassis until the front of the card
makes contact with the connector inside the chassis.
7. Press the card firmly into the slot until the connector
plate is flush with the rear panel of the chassis and the
connector is fully seated.
8. Using a Phillips screwdriver, tighten the retaining screws
at the top and bottom of the card to secure it to the chassis.
makes contact with the connector inside the chassis.
7. Press the card firmly into the slot until the connector
plate is flush with the rear panel of the chassis and the
connector is fully seated.
8. Using a Phillips screwdriver, tighten the retaining screws
at the top and bottom of the card to secure it to the chassis.
9. Power on the VS-1616D and follow the procedure in the
VS-1616D User Manual (see Section 9) to configure the new
card.
VS-1616D User Manual (see Section 9) to configure the new
card.
10. Power on the peripheral devices.
To install an I/O card:
1. Power off the VS-1616D and all devices
connected to it.
connected to it.
2. Using a Phillips screwdriver, loosen the
screws at the top and bottom of the
blanking plate.
screws at the top and bottom of the
blanking plate.
3. Remove the blanking plate from the slot
and store it for possible future use.
and store it for possible future use.
4. Remove the new card from its shipping
box and anti-ESD bag.
box and anti-ESD bag.
The VS-1616D HDMI I/O Card mounts in one of the 16 slots on the rear of the
chassis. Slots are numbered from left to right and must be filled consecutively from left to
right, without leaving empty slots.
chassis. Slots are numbered from left to right and must be filled consecutively from left to
right, without leaving empty slots.
WARNING: An input card must only be mounted in a slot designated for input cards (slots
1 to 4 and 9 to 12) and an output card must only be mounted in a slot designated for
output cards (slots 5 to 8 and 13 to 16).
1 to 4 and 9 to 12) and an output card must only be mounted in a slot designated for
output cards (slots 5 to 8 and 13 to 16).
VS-1616D
O
UT
HD
M
I
IN
IN
IN
IN
O
UT
O
UT
O
UT
O
UT
O
UT
O
UT
O
UT
O
UT
IN
IN
IN
IN
1
3
3
5
5
7
7
1
9
9
11
11
13
13
15
15
2
4
4
6
6
8
8
2
10
10
12
12
14
14
16
16
C
T
R
L
HD
M
I
HD
M
I
DV
I
DL
DV
I
DV
I
DV
I
DL
DV
I
DV
I
DV
I
DL
HD
M
I
DV
I
DL
TE
ST
C
T
R
L
TE
ST
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
O
UT
O
UT
O
UT
O
UT
O
UT
O
UT
O
UT
R
S
2
3
2
N
E
T
P
O
W
E
R
L
IN
K
P
A
T
T
E
R
N
R
E
S
O
L
U
T
IO
N
O
UT
HD
M
I