Cobra Electronics 25 LX Manuel Du Propriétaire
Operation
Operation
19
18
Setting
Brightness
Mode
Setting Brightness Mode
Press Menu/Enter knob to select Set Brightness
Rotate Menu/Enter knob clockwise to Select
Brightness. Press Menu/Enter knob to select
Day-Bright. Turn Menu/Enter clockwise to
increase brightness and turn counter-clockwise to
decrease brightness.
increase brightness and turn counter-clockwise to
decrease brightness.
To set the day bright level, turn the Menu/Enter
knob clockwise to a desired setting and then
press Menu/Enter. To set the Night-Dim level,
repeat instructions above then select Night-Dim.
knob clockwise to a desired setting and then
press Menu/Enter. To set the Night-Dim level,
repeat instructions above then select Night-Dim.
Press Menu/Enter knob again to exit routine.
Note
If an attempt is made to
exceed the highest or lowest
brightness levels, 1 error beep
will be heard.
If an attempt is made to
exceed the highest or lowest
brightness levels, 1 error beep
will be heard.
DAY-BRIGHT
NIGHT-DIM
SET BRIGHTNESS
SET LEVEL
EXIT
TURN CH KNOB TO
Note
Exit will return to menu mode.
ESC will exit and return to CB
Standby.
Exit will return to menu mode.
ESC will exit and return to CB
Standby.
Weather Auto
Scan
DAY-BRIGHT
NIGHT-DIM
SET BRIGHTNESS
Note
To select day or night levels,
press and release Dim/Escape
button once levels are set.
To select day or night levels,
press and release Dim/Escape
button once levels are set.
Note
To toggle from day to night
settings, see page 27.
To toggle from day to night
settings, see page 27.
Setting
Contrast Mode
Setting Contrast Mode
Press Menu/Enter knob and rotate clockwise to
select Set Contrast. Press Menu/Enter knob
again and rotate clockwise to increase contrast,
counter-clockwise to decrease contrast.
Press Menu/Enter knob to set contrast.
select Set Contrast. Press Menu/Enter knob
again and rotate clockwise to increase contrast,
counter-clockwise to decrease contrast.
Press Menu/Enter knob to set contrast.
Press Menu/Enter knob again to exit routine.
Note
If an attempt is made to
exceed the highest or lowest
contrast levels, 1 error beep will
be heard.
If an attempt is made to
exceed the highest or lowest
contrast levels, 1 error beep will
be heard.
SET CONTRAST
EXIT
TURN CH KNOB TO
Key Tones
Mode
Key Tones Mode On and Off
Press Menu/Enter knob and rotate clockwise
to Set Key Tones. Press Menu/Enter to set Key
Tones On/Off.
to Set Key Tones. Press Menu/Enter to set Key
Tones On/Off.
Press Menu/Enter knob to select On/Off and
exit to main menu.
exit to main menu.
Note
Press Dim/Escape
button to return to CB mode.
Press Dim/Escape
button to return to CB mode.
Radio Check
Mode
Radio Check Mode
Allows testing of important radio functions.
Test 1- Battery Level: Confirms that battery
voltage level is between 10.8 V to 15.8 V. If in that
range, it is “PASS”. Outside of that range, either
FAIL LOW” or “FAIL HIGH” will be displayed. Press
Test 1- Battery Level: Confirms that battery
voltage level is between 10.8 V to 15.8 V. If in that
range, it is “PASS”. Outside of that range, either
FAIL LOW” or “FAIL HIGH” will be displayed. Press
Menu/Enter knob to advance to next test.
Note
Press Dim/Escape button to
return to CB standby mode.
If 10 seconds pass or if Enter
button pressed, unit goes to
2nd test.
Press Dim/Escape button to
return to CB standby mode.
If 10 seconds pass or if Enter
button pressed, unit goes to
2nd test.
SIG
+30dB
1
1
2 3 4 TX PWR
3
5 7 9
MEM
NB
TX
RX
VOL
SQ
OFF
DYNAMIKE
MIN
RF GAIN
MIN
MAX
M
EN
U PU
SH ENT
ER
SCAN / M SCAN
DIM / ESC
CB / PA
NB
CH9 / 19
BATTERY VOLTAGE
FAIL LOW
FAIL LOW
Test 2- RF Power Output: Confirms 3.3 to 4 Watt
output level. Once Push-to-Talk button is pressed,
Pass or Fail will be displayed if level is outside limits.
output level. Once Push-to-Talk button is pressed,
Pass or Fail will be displayed if level is outside limits.
Note
Press Dim/Escape button to
return to CB standby mode. If
10 seconds pass or if Enter button
pressed, go to 3rd test.
Press Dim/Escape button to
return to CB standby mode. If
10 seconds pass or if Enter button
pressed, go to 3rd test.
Note
Press Push-To-Talk within 10
seconds or unit will go to the
next test.
Press Push-To-Talk within 10
seconds or unit will go to the
next test.
SIG
+30dB
1
1
2 3 4 TX PWR
3
5 7 9
MEM
NB
TX
RX
VOL
SQ
OFF
DYNAMIKE
MIN
RF GAIN
MIN
MAX
M
EN
U PU
SH ENT
ER
SCAN / M SCAN
DIM / ESC
CB / PA
NB
CH9 / 19
RF POWER OUTPUT
PASS
PASS
SIG
+30dB
1
1
2 3 4 TX PWR
3
5 7 9
MEM
NB
TX
RX
VOL
SQ
OFF
DYNAMIKE
MIN
RF GAIN
MIN
MAX
M
EN
U PU
SH ENT
ER
SCAN / M SCAN
DIM / ESC
CB / PA
NB
CH9 / 19
RF POWER OUTPUT
FAIL
FAIL
Note
Press Dim/Escape button to
return to CB standby mode.
If 10 seconds pass or if Enter
button pressed, testing is
complete. Unit will return to
CB Standby mode.
Press Dim/Escape button to
return to CB standby mode.
If 10 seconds pass or if Enter
button pressed, testing is
complete. Unit will return to
CB Standby mode.
1
2
3
1
2
3
SIG
+30dB
1
1
2 3 4 TX PWR
3
5 7 9
MEM
NB
TX
RX
VOL
SQ
OFF
DYNAMIKE
MIN
RF GAIN
MIN
MAX
M
EN
U PU
SH ENT
ER
SCAN / M SCAN
DIM / ESC
CB / PA
NB
CH9 / 19
BATTERY VOLTAGE
FAIL HIGH
FAIL HIGH
SIG
+30dB
1
1
2 3 4 TX PWR
3
5 7 9
MEM
NB
TX
RX
VOL
SQ
OFF
DYNAMIKE
MIN
RF GAIN
MIN
MAX
M
EN
U PU
SH ENT
ER
SCAN / M SCAN
DIM / ESC
CB / PA
NB
CH9 / 19
PRESS PTT
TO CHECK
TO CHECK
POWER OUTPUT
25LX_MANL.indd 18-19
11/15/11 9:43 AM