DYMO Dymo Clock DATEMARK Fascicule

In Program mode,

change field values.

Select message to print.
In program mode, move

between fields.

Set alarm.

Set a security

code to lock your
stamper settings.

Change
stamper settings.

Select fields
to print.

DISTRIBUTED BY/DISTRIBUÉ PAR:

IMPORTED INTO CANADA BY/IMPORTÉ AU CANADA

PAR SANFORD CANADA L.P., OAKVILLE, ON L6J 3J3

Getting Started

Inserting the Batteries

1 Press the thumb latch on

the back of the stamper
to remove the battery
compartment cover.

2 Insert four AA batteries

following the polarity
markings (+ and -).

3 Using a coin, remove

the lithium cell battery
compartment cover.

4 Remove the safety

ribbon and make sure
the positive (+) side of
the battery is facing up.

5 Replace the lithium cell

battery compartment
cover. Use a coin to
lock the cover in place.

6 If the LCD display

flashes P-RESET,
use a ballpoint pen to
press the reset button.

7 Replace the battery

compartment cover.

Setting the Date and Time

1 Press and hold the SET/EDIT button for 2

seconds.
The stamper enters Program mode and the
Month (M) and Day (D) indicators begin flashing.

If no keys are pressed for 10 seconds, the

stamper returns to Normal mode.

2 Press the LOCK button to cycle through the

available date formats.

3 Select one of the following date formats, and

then press the SHIFT button.

•  MM-DD-YY
•  YY-MM-DD
•  DD-MM-YY

4 To set the value for the first field, do the

following:

• To increase the value, press the

LOCK button.

• To decrease the value, press and hold the

LOCK and SHIFT buttons for 5 seconds,
and then press the LOCK button to
decrease the value.

5 Press the SHIFT button to move to the next field.
6 Repeat steps 4 and 5 to set the value for

each field.

7 Press the SET/EDIT button to return to

Normal mode.

3 Press the SHIFT button to move to the

next digit.

4 Repeat steps 2 and 3 for each digit.
5 Press the SECURITY CODE button to unlock

the stamper and return to Normal mode.
The key icon disappears from the display.

If you have forgotten the security code, remove

and replace the lithium cell battery to reset the
code. Removing the lithium cell battery resets all
stamper settings.

Resetting the Stamper

If the AA batteries are low or there is a printer error,
the display will flash P-RESET. The stamper will not
print while P-RESET is flashing. You must reset the
stamper in order to print.

1 Press the thumb latch on

the back of the stamper
to remove the battery
compartment cover.

2 Use a ballpoint pen to

press the PRINTER
RESET button.
The printing belt is reset.

If you do not hear the printing belt reset,

replace the four AA batteries and press the
PRINTER RESET button again.

Maintaining the Stamper

To maintain your stamper at peak operating
performance, follow these guidelines:

Do not touch the print head or belt when the
unit is printing. This will cause the printer to
malfunction and require servicing.

If printer speed slows down, replace all four
AA batteries. Operating the stamper with low
batteries will damage the stamper.

Immediately replace the lithium cell display
battery if BATT appears in the display.

Always cover the battery compartment
before printing.

Keep stamper away from moisture.

Avoid placing stamper in direct sunlight.

Before printing, ensure paper surface is dust
free and print head is clean.

When printing, place the paper on an
even surface.

To clean the exterior of the stamper and the
battery compartment, wipe with a lint-free
cloth. Remove dirt and smudges using a cotton
ball and alcohol.

Ensure surroundings are clean and free of
dust before performing maintenance on the
stamper.

Perform stamper maintenance every three
months to prevent particle accumulation on the
print head.

Using tweezers, carefully remove any dried ink
from the roller and then clean using a lint-free
cloth or cotton ball and alcohol.

Clean stamper before storing if the stamper will
not be used for an extended period of time.

Maintaining the Battery
The stamper checks the status of the display
battery every hour. If the lithium cell display battery
is low, BATT appears in the display.
IMPORTANT: If BATT appears in the display,
change the lithium cell battery immediately.
Operating the stamper on a low display battery
may cause damage to the stamper.

Refilling the Ink Roll

1 Remove the ink roll compartment cover.
2 Using tweezers or a paper

clip, rotate the ink roll
counter-clockwise and
pull the ink roll to remove
from the stamper.

3 Apply a few drops of ink

pad ink on the ink roll.

4 Carefully insert the ink

roll in the proper position
inside the stamper.

5 Replace the ink roll

compartment cover.

Selected Fields

Display

Example

Date and Time

26-12-12 P12:38

Date, Time,
and Message

26-12-12 P12:38 RCVD

Date, Message,
and 4-digit counter

26-12-12 RCVD 1234

Date and
6-digit counter

26-12-12 000456

Message

OUT

PAID

FILE

REFERENCE

CONFIRMED

RECEIVED

Abbreviation

OUT

PAID

FILE

REF:

CFMD

RCVD

Selecting the Fields to Print
You can print any combination of the
following fields:

Date

Time

Message

You can also choose to print any of the two fields
above and a 4-digit counter or any one of the fields
above with a 6-digit counter.

1 Press and hold the PRINT SELECT button for

2 seconds.
The date field begins flashing.

2 Press the SET/EDIT button to select or not

select to print the field.

3 Press the PRINT SELECT button to move to

the next field.

4 To select to print the date, do the following:

a Press the SET/EDIT button until a rectangle

is displayed around DATE in the display.

b Press the PRINT SELECT button to move

to the next field.

5 Repeat step 4 for each remaining field.
6 Press the ALARM MODE button to return to

Normal mode.

Selecting the Message to Print
When you select to print the message field, you
can also select which message to print.

Press the SHIFT button to select the message
to print.
Each time you press the SHIFT button, the
next available message is selected.

Printing

1 Set the stamper on a clean, flat surface.
2 Rock the stamper forward and push down on

the top of the stamper.
The stamper prints the selected fields.

3 When you hear that printing has finished,

release pressure on the stamper.

Using Auto-Numbering

Setting Auto-Numbering
You can print a 4-digit or 6-digit counter. A 4-digit
counter can be combined with any two additional
fields. A 6-digit counter can be combined with any
one additional field.

1 Press and hold the PRINT SELECT button for

2 seconds.
The date field begins flashing.

2 Press the PRINT SELECT button until the

desired counter type is flashing.

•  4-DIGIT - counts up
•  q 6-DIGIT - counts down
•  6-DIGIT p - counts up

3 Press the SET/EDIT button until a rectangle is

displayed around the selected counter.

4 To set the first digit, do the following:

a Press the LOCK button to increase

the value.

b Press the SHIFT button to move to the

next digit.

5 Repeat step 4 for each digit.
6 Press the ALARM MODE button to return to

Normal mode.

Locking Auto-Numbering
You can choose to lock auto-numbering so that
the counter does not automatically increment to
the next number after each printing.

Press the LOCK button.
CNTLOCK appears in the display.

To unlock auto-numbering, press the

LOCK button again.

Using the Alarm

Setting the Alarm

1 Press the ALARM MODE button.

The alarm indicator begins flashing.

2 Press the LOCK button to activate the alarm.

The alarm icon appears in the display.

3 Press the SET/EDIT button while the alarm

indicator is still flashing.
The hour field begins flashing.

4 Press the LOCK button to set the hour, and

then press the SHIFT button.

5 Press the LOCK button to set the minute.
6 Press the ALARM MODE button to save the

alarm settings and return to Normal mode.

When the alarm sounds, press the ALARM MODE
button to stop the alarm.

Turning Off the Alarm

1 Press the ALARM MODE button.

The alarm indicator begins flashing.

2 Press the LOCK button to deactivate the alarm.

The alarm icon disappears from the display.

Using a Security Code

To prevent unauthorized changing of stamper or
counter settings, you can use a four digit security
code to lock your stamper.
Locking the Stamper

1 Press and hold the SECURITY CODE button

for 2 seconds.
The first digit of the security code begins
flashing.

2 Press the LOCK button to set the first digit.
3 Press the SHIFT button to move to the

next digit.

4 Repeat steps 2 and 3 for each digit.
5 Press the SECURITY CODE button to lock the

stamper and return to Normal mode.
A key icon appears in the display.

Unlocking the Stamper

1 Press and hold the SECURITY CODE button

for 2 seconds.

2 Press the LOCK button to select the first digit

of the code.

W010793