Panasonic Attune Mode D’Emploi
14
Note:
• If POS Remote is set for ON, you have to note that no
button operation of the Beep Day/Night is possible at the
center module.
center module.
DAY mode: When you are taking charge of lane A, if the
vehicle detector is on the lane A, you will hear the beep
A. If the vehicle detector is on of the lane B, you will not
hear the beep B.
A. If the vehicle detector is on of the lane B, you will not
hear the beep B.
NIGHT mode: When you are taking charge of lane A, if the
vehicle detector is on the lane A, you will hear the beep
A. If the vehicle detector is on of the lane B, you will hear
the low level beep B. When both vehicle detectors are
on, you will alternately hear the beep A and the low level
beep B.
A. If the vehicle detector is on of the lane B, you will hear
the low level beep B. When both vehicle detectors are
on, you will alternately hear the beep A and the low level
beep B.
5. When the delay is necessary for the message
When the customer approaches the menu board, the
message is output after a delay of 2 seconds. Press the
Greeter Start Delay Button of the Center Module. The
Greeter Start Delay Indicator will light in yellow.
message is output after a delay of 2 seconds. Press the
Greeter Start Delay Button of the Center Module. The
Greeter Start Delay Indicator will light in yellow.
● Vehicle Detector BEEP DAY/NIGHT
In the case of Double Drive-Thru configuration, it is possible
to select the Vehicle Detector Beep tone to be heard when a
customer approaches the menu board.
Day/Night setup can be made by button operation at the
front panel of this unit.
When the Day mode is set, the Beep Day/Night indicator of
the center module will light in yellow. When the Beep
Day/Night button is pressed, the Night mode is assumed
and this indicator will disappear.
to select the Vehicle Detector Beep tone to be heard when a
customer approaches the menu board.
Day/Night setup can be made by button operation at the
front panel of this unit.
When the Day mode is set, the Beep Day/Night indicator of
the center module will light in yellow. When the Beep
Day/Night button is pressed, the Night mode is assumed
and this indicator will disappear.
DAY/NIGHT
Vehicle detector
Order Taker and All-in-One Headset
Lane A is ON
Lane B is ON
A
B
DAY
b
–
Beep A
–
–
b
–
Beep B
b
b
Beep A
Beep B
NIGHT
b
–
Beep A
Low level Beep A
–
b
Low level Beep B
Beep B
b
b
Beep A +
Low level beep B (*1)
Beep B +
Low level beep A (*2)
OPERATIONAL SETTING
SPEED
TEAM
BEEP
DAY/NIGHT
ON:DAY
OUTSIDE
SP LEVEL
ON:DAY
V/DET
OVERRIDE
T/P
RELEASE
Vehicle Detector Beep DAY/NIGHT Button
*1: When you press the button T1, the beep will change to low level beep B only.
*2: When you press the button T1, the beep will change to low level beep A only.
*2: When you press the button T1, the beep will change to low level beep A only.
● Outside Speaker Level DAY/NIGHT
The Outside Speaker level can be set up.
Day/Night setup can be made by button operation at the
front panel of this unit.
Day/Night setup can be made by button operation at the
front panel of this unit.
OPERATIONAL SETTING
SPEED
TEAM
BEEP
DAY/NIGHT
ON:DAY
OUTSIDE
SP LEVEL
ON:DAY
V/DET
OVERRIDE
T/P
PELEASE
Outside Speaker Level DAY/NIGHT Button
When the Day mode is set, the Outside SP Level indicator of
the center module will light in yellow. When the Outside SP
Level button is pressed, the Night mode is assumed and
this indicator will disappear.
the center module will light in yellow. When the Outside SP
Level button is pressed, the Night mode is assumed and
this indicator will disappear.
DAY mode: Normal level
NIGHT mode: 50% level (Attenuation)
NIGHT mode: 50% level (Attenuation)
Note:
• If POS Remote is set for ON, you have to note that no
button operation of the Outside Speaker Level is possi-
ble at the center module.
ble at the center module.