Atdec Spacedec Acrobat Articulated Arm SD-AT-DK-S Fascicule
C.1. Bolt Through
Mounting Options
C
C.2. Desk Clamp
There are two Mounting Options: Desk Clamp and Bolt Through
To use the Bolt Through system (Suits desktop thicknesses of 12mm-40mm [
To use the Bolt Through system (Suits desktop thicknesses of 12mm-40mm [
1
/
2
”
-1
1
/
2
”
]) follow the Bolt
Through instructions at C.1. To use the Desk Clamp (Suits destop thicknesses of 12mm-38mm [
1
/
2
”
-1
1
/
2
”
])
follow the Desk Clamp instructions at C.2.
Attaching the Display
D
Direct Mount Configuration
75mm x 75mm (3” x 3”) mounting hole pattern
100mm x 100mm (4” x 4”) mounting hole pattern
Installing Cable Management
E
Attaching the Cable Wrap to the Arm
F
E.1.
Push the four supplied Cable Clips into the holes on the underside of the arm as shown in diagram
E.2.
Feed the cables into the Cable Wrap Applicator.
E.3.
Insert the Cable Wrap Applicator into the Cable Wrap as shown.
E.4.
Squeeze the nose of the Applicator and place inside the Cable Wrap ensuring that the opening edges
of the Cable Wrap face towards the nose of the applicator as shown in diagram.
F.1.
Position the display at its highest possible
position to ensure that there is sufficient
cabling at the end of the arm so the cables
are not stretched or pulled out when the
display is moved.
cabling at the end of the arm so the cables
are not stretched or pulled out when the
display is moved.
F.2.
Clip the cable wrap into the four Cable
Clips as shown in diagram.
Cable Clips
Display at
highest point
highest point
E.1.
Push in
Clips
Clips
NOTE:
Ensure that
the flat side of
each Extension
Clip sits against
the back of the
display
Extension Clip
4x12mm or
4x16mm Screws
4x16mm Screws
Display
4x10mm
Screws
Screws
C.1.1. Base Casting
The Articulated Arm is limited to 180° rotation. This is
determined by the location of the Base Casting, as shown.
determined by the location of the Base Casting, as shown.
When mounting the Base Casting, ensure that the
Articulated Arm is free to achieve its full 180° range of
movement.
Articulated Arm is free to achieve its full 180° range of
movement.
If mounting the Base Casting in a 90° corner, position the
casting to ensure that the Articulated Arm can only make
contact with one side of the corner.
casting to ensure that the Articulated Arm can only make
contact with one side of the corner.
The Base Casting should be mounted no less than
50mm (2”) from the edge of the desk.
50mm (2”) from the edge of the desk.
C.1.2. Drill Mounting Hole
Position the Base Casting on the desk in the
desired location ensuring that the letter “F”
faces the user. Using the base casting position,
locate and mark the holes (x3) for drilling.
Position the Base Casting on the desk in the
desired location ensuring that the letter “F”
faces the user. Using the base casting position,
locate and mark the holes (x3) for drilling.
Drill the holes and then secure the Base
Casting to the desk using the supplied 14
Gauge Self Tapping Screws (x2).
Casting to the desk using the supplied 14
Gauge Self Tapping Screws (x2).
C.2.1. Assemble Desk Clamp
Place the Base Casting on top of the Desk
Clamp ensuring the “F” is facing towards the
user. Using the 4mm Allen Key, attach the Base
Casting to the clamp by inserting the supplied
M6x12mm Countersunk Screws (x2) into the
holes in the Base Casting as shown.
Clamp ensuring the “F” is facing towards the
user. Using the 4mm Allen Key, attach the Base
Casting to the clamp by inserting the supplied
M6x12mm Countersunk Screws (x2) into the
holes in the Base Casting as shown.
BEFORE PROCEEDING TO THE NEXT STEP PLEASE NOTE:
Articulated Arm will only work when a display is properly installed.
DO NOT
adjust tension screws or gas strut until your display has been attached.
14 Guage
Self Tapping
Screw
Desktop
3mm Hole
(
1/8
”)
15mm Hole (
9/16
”)
Base
Casting
Casting
User
C.1.3. Installing the Articulated Arm
Insert the M10 Interscrew up through the hole in the
work surface.
Insert the M10 Interscrew up through the hole in the
work surface.
Using both hands, secure the M10 Interscrew with
the 5mm Allen Key and use the other hand to
tighten the Threaded Rod into the Interscrew with
the supplied Top Cap Tool.
the 5mm Allen Key and use the other hand to
tighten the Threaded Rod into the Interscrew with
the supplied Top Cap Tool.
C.2.2. Attaching the Desk Clamp
Place the Desk Clamp in the desired position on the
edge of the dektop and secure in place using the
supplied 5mm Allen Key as shown in diagram.
edge of the dektop and secure in place using the
supplied 5mm Allen Key as shown in diagram.
C.2.3. Attaching the Articulated Arm
Use the Top Cap Tool to tighten the Threaded
Rod into the Base Casting as shown.
Rod into the Base Casting as shown.
Top Cap Tool
NOTE:
Desk Clamp Assembly is
Suitable for square edged desks only
DESK CLAMP ADJUSTMENT RANGE
NOTE:
It is
recommended
that the Desk
Clamp be
attached to
the rear or
side edge of
the work
surface
Adjust the Desk Clamp to suit your desk
thickness by turning the M8 Desk Clamp Screw
with the supplied 5mm Allen Key.
thickness by turning the M8 Desk Clamp Screw
with the supplied 5mm Allen Key.
Suits 12mm (
1/2
”) to
38mm (1
1/2
”) thick
Work Surfaces
Pressure Plate (x2)
M8 Desk Clamp
Screw (x2)
Screw (x2)
Nose
E.2.
E.3.
E.4.
Tighten
Firmly
Firmly
12mm
Countersunk
Screws (x2)
Countersunk
Screws (x2)
Base
Casting
4mm
Allen Key
Allen Key
Desk
Clamp
Assembly
Tighten
Firmly
Firmly
Cable Wrap
100mm
(4”)
100mm (4”)
75mm
(3”)
75mm (3”)
Display
5mm Allen Key
Top Cap
Tool
Tool
Tighten
Firmly
Firmly
Tighten Firmly
Washer
M8 Desk
Clamp
Screw
Clamp
Screw
Desk
Clamp
Assembly
Threaded
Rod
5mm Allen Key
Tighten
Firmly
Towards User
Desktop
Base
Casting’s
Tongue
Inner Tube
Slot
NOTE:
When attaching the
Articulated Arm,
ensure the Base
Casting’s Tongue
is inserted into the
Inner Tube Slot as
shown in C.2.2.
Articulated
Arm
50mm
(2”)
180° Rotation
Desktop
180°
NOTE:
Ensure the Base
Casting’s Tongue is
inserted in to the Inner
Tube Slot when securing
the arm assembly
Inner Tube Slot
Base
Casting’s
Tongue
Casting’s
Tongue
M10 Interscrew