Brocade Communications Systems Brocade ICX 6650 6650 Manuel D’Utilisation
Brocade ICX 6650 Security Configuration Guide
269
53-1002601-01
TCP SYN attacks
Syntax: ip icmp burst-normal value burst-max value lockup seconds
The burst-normal value parameter can be from 1 through 100,000 packets per second.
The burst-max value parameter can be from 1 through 100,000 packets per second.
The lockup value parameter can be from 1 through 10,000 seconds.
This command is supported on Ethernet and Layer 3 interfaces.
The number of incoming ICMP packets per second is measured and compared to the threshold
values as follows:
values as follows:
•
If the number of ICMP packets exceeds the burst-normal value, the excess ICMP packets are
dropped.
dropped.
•
If the number of ICMP packets exceeds the burst-max value, all ICMP packets are dropped for
the number of seconds specified by the lockup value. When the lockup period expires, the
packet counter is reset and measurement is restarted.
the number of seconds specified by the lockup value. When the lockup period expires, the
packet counter is reset and measurement is restarted.
In the example, if the number of ICMP packets received per second exceeds 5,000, the excess
packets are dropped. If the number of ICMP packets received per second exceeds 10,000, the
device drops all ICMP packets for the next 300 seconds (5 minutes).
packets are dropped. If the number of ICMP packets received per second exceeds 10,000, the
device drops all ICMP packets for the next 300 seconds (5 minutes).
TCP SYN attacks
TCP SYN attacks exploit the process of how TCP connections are established to disrupt normal
traffic flow. When a TCP connection starts, the connecting host first sends a TCP SYN packet to the
destination host. The destination host responds with a SYN ACK packet, and the connecting host
sends back an ACK packet. This process, known as a “TCP three-way handshake,” establishes the
TCP connection.
traffic flow. When a TCP connection starts, the connecting host first sends a TCP SYN packet to the
destination host. The destination host responds with a SYN ACK packet, and the connecting host
sends back an ACK packet. This process, known as a “TCP three-way handshake,” establishes the
TCP connection.
While waiting for the connecting host to send an ACK packet, the destination host keeps track of
the as-yet incomplete TCP connection in a connection queue. When the ACK packet is received,
information about the connection is removed from the connection queue. Usually there is not much
time between the destination host sending a SYN ACK packet and the source host sending an ACK
packet, so the connection queue clears quickly.
the as-yet incomplete TCP connection in a connection queue. When the ACK packet is received,
information about the connection is removed from the connection queue. Usually there is not much
time between the destination host sending a SYN ACK packet and the source host sending an ACK
packet, so the connection queue clears quickly.
In a TCP SYN attack, an attacker floods a host with TCP SYN packets that have random source IP
addresses. For each of these TCP SYN packets, the destination host responds with a SYN ACK
packet and adds information to the connection queue. However, because the source host does not
exist, no ACK packet is sent back to the destination host, and an entry remains in the connection
queue until it ages out (after approximately a minute). If the attacker sends enough TCP SYN
packets, the connection queue can fill up, and service can be denied to legitimate TCP
connections.
addresses. For each of these TCP SYN packets, the destination host responds with a SYN ACK
packet and adds information to the connection queue. However, because the source host does not
exist, no ACK packet is sent back to the destination host, and an entry remains in the connection
queue until it ages out (after approximately a minute). If the attacker sends enough TCP SYN
packets, the connection queue can fill up, and service can be denied to legitimate TCP
connections.
To protect against TCP SYN attacks, you can configure the Brocade device to drop TCP SYN packets
when excessive numbers are encountered. You can set threshold values for TCP SYN packets that
are targeted at the router itself or passing through an interface, and drop them when the
thresholds are exceeded.
when excessive numbers are encountered. You can set threshold values for TCP SYN packets that
are targeted at the router itself or passing through an interface, and drop them when the
thresholds are exceeded.
For example, to set threshold values for TCP SYN packets targeted at the router, enter the following
command in global CONFIG mode.
command in global CONFIG mode.
Brocade(config)# ip tcp burst-normal 10 burst-max 100 lockup 300
To set threshold values for TCP SYN packets received on interface 1/1/3, enter the following
commands.
commands.