Microsmith Emitter Expansion Kit EXPX6 Fascicule
Mount the Green LED in a very discrete slot using the adhesive tab. When functioning properly, the LED
is off when not receiving a remote command, blinks when activated by a remote control, or blinks once upon
unplugging the Receiving Eye's RCA connector at the Repeater Box. The LED lights inadvertently if detecting
spurious IR or LF RF entering the Receiver Eye. See Receiver Eye details for tips on eliminating noise.
is off when not receiving a remote command, blinks when activated by a remote control, or blinks once upon
unplugging the Receiving Eye's RCA connector at the Repeater Box. The LED lights inadvertently if detecting
spurious IR or LF RF entering the Receiver Eye. See Receiver Eye details for tips on eliminating noise.
Hook up the Plug-in Power Supply by simply plugging in the connector at the end of the cord into the power input
connector on the back of the Repeater Box, then plug Power Supply into suitable 110-120 Volt standard wall outlet.
connector on the back of the Repeater Box, then plug Power Supply into suitable 110-120 Volt standard wall outlet.
Verify operation by first turning your system on with the remote control. Verify further by testing various remote
commands with the equipment hidden. Next try aiming remote control at furniture, walls, floor and ceiling, etc. to find
infrared light reflecting objects to bounce commands to the HOT LINK PRO! Remote Control Booster and your home
theater system.
commands with the equipment hidden. Next try aiming remote control at furniture, walls, floor and ceiling, etc. to find
infrared light reflecting objects to bounce commands to the HOT LINK PRO! Remote Control Booster and your home
theater system.
The HOT LINK PRO! automatically extends its range as ambient light decreases, and hence has more sensitivity the
darker the surrounding light. It may perform slightly differently in the day than at night. HOT LINK PRO! receives
remote commands even if your equipment is behind you or overhead, like projection televisions. High-efficiency
screw-in type fluorescent lights and some radio-type IR repeaters can interfere with HOT LINK PRO! Some receivers
use high frequency remote controls above 60Khz that are not repeatable through Hot Link Pro!
Remember to keep your remote batteries fresh.
darker the surrounding light. It may perform slightly differently in the day than at night. HOT LINK PRO! receives
remote commands even if your equipment is behind you or overhead, like projection televisions. High-efficiency
screw-in type fluorescent lights and some radio-type IR repeaters can interfere with HOT LINK PRO! Some receivers
use high frequency remote controls above 60Khz that are not repeatable through Hot Link Pro!
Remember to keep your remote batteries fresh.
The Repeater Box is well shielded by an internal metal box and stands up to a great deal of RF noise injection.
However, with enough RF noise it is possible to inject noise into the Emitter wires if they are too close to the fly-back
transformer in a TV set. Avoid bundling emitter wires near the back of the TV. For rear screen projection sets, the
fly-back transformers are mounted in the lower part of the TV set and can be easily avoided.
However, with enough RF noise it is possible to inject noise into the Emitter wires if they are too close to the fly-back
transformer in a TV set. Avoid bundling emitter wires near the back of the TV. For rear screen projection sets, the
fly-back transformers are mounted in the lower part of the TV set and can be easily avoided.
CD Loader
RIGHT
WRONG
Stay clear of doors
Do not block doors
For indoor use only.
Liability of product limited to cost of product replacement.
Non-specified use is the responsibility of the user.
DO NOT OPEN Power Supply or Repeater Box: No user serviceable parts inside.
Do not expose HOT LINK PRO! to water, moisture or rain.
Connect only to 110-120 VAC. Or 12VDC using fused Power Adapter
Refer servicing to qualified personnel. Read all instructions before use, retain for future reference.
Liability of product limited to cost of product replacement.
Non-specified use is the responsibility of the user.
DO NOT OPEN Power Supply or Repeater Box: No user serviceable parts inside.
Do not expose HOT LINK PRO! to water, moisture or rain.
Connect only to 110-120 VAC. Or 12VDC using fused Power Adapter
Refer servicing to qualified personnel. Read all instructions before use, retain for future reference.
INC.
WWW.HOT-LINK.COM
P.O. BOX 7829
Jackson, WY 83002
Jackson, WY 83002
Route wires to avoid covering tape/disc slots and doors on equipment that might pull Emitter wires upon opening or
jamb on wires when closing. Lengthening emitter wires requires marking polarity before cutting.
Factory custom lengths available to 25 feet.
jamb on wires when closing. Lengthening emitter wires requires marking polarity before cutting.
Factory custom lengths available to 25 feet.
Non-contact option: Peel off double-stick tape
from Emitter, tape wire to shelf or clamp wire
under a foot of one piece of equipment. Then
bend wire so that it holds the Emitter in front
of, and pointing at, the "EYE" on the
equipment, up to three inches away.
from Emitter, tape wire to shelf or clamp wire
under a foot of one piece of equipment. Then
bend wire so that it holds the Emitter in front
of, and pointing at, the "EYE" on the
equipment, up to three inches away.
Emitters, Continued...
Power Supply
Green Confirmation LED
Repeater Box and Emitter Wires
System Check
Operating Tips
Accessories
Additional Receiver Eye for connecting to other IR emitters, supplied with "Y" RCA adapter
Coax Extender Cable, custom lengths to 25 feet. (additional length may reduce IR distance)
12 Volt Adapter with fuse for use in motor homes
Power Supply for use with 120VAC
Replacement adhesive tape, free for the asking
Coax Extender Cable, custom lengths to 25 feet. (additional length may reduce IR distance)
12 Volt Adapter with fuse for use in motor homes
Power Supply for use with 120VAC
Replacement adhesive tape, free for the asking
PDF created with pdfFactory trial version