Napoleon BIP500RBNSS Manuel

www.napoleongrills.com

This Gas Barbecue Is Certified Under Canadian And American National Standards, CSA 1.6a-2008 and ANSI 

Z21.58a-2008 respectively for Outdoor Gas Grills and should be installed to conform with local codes. In 

absence of local codes, install to the current CAN/CSA-B149.1 Propane Installation Code in Canada or to 

the National Fuel Gas Code, ANSI Z223.1 in the United States. 
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence 

of local codes, with the current CSA C22.1  Canadian Electrical Code in Canada or the National Electrical 

Code, ANSI/NFPA 70 in the United States.
CALIFORNIA PROPOSITION 65: The burning of gas fuel creates by-products, some of which are on the list 

as substances known by the State of California to cause cancer or reproductive harm.  When cooking with 

gas, always ensure adequate ventilation to the unit, to minimize exposure to such substances.

If the gas grill is being supplied with propane from a portable cylinder, a regulator specified by the 

manufacturer must be used.  The regulator must supply a pressure of 11 inches water column (0.39 PSI) to 

the gas grill and have a QCC1 type fitting. Cylinders to be used with this unit must be supplied with a QCC1 

cylinder valve.  A QCC1 cylinder has a positive seating connection, which will not allow gas flow until a 

positive seal has been achieved.  It is also equipped with an excess flow device.  In order to attain full flow 

to the grill, the valves must be in the off position when the cylinder valve is turned on.  
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never 

use a cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in 

accordance with the specifications for LP-gas cylinders of the National Standard of Canada, CAN/CSA-b339, 

Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable or 

the Specifications for LP-Gas Cylinders of the U.S. Department of Transportation (D.O.T.). Cart models have 

been designed for use with a 20 lb (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connection device compatible with the connection 

for outdoor cooking appliances.  The propane cylinder must be provided with a shut-off valve terminating 

in a propane cylinder valve type QCC1, and a safety relief device having direct communication with the 

vapor space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the 

cylinder shall include a collar to protect the cylinder valve.  The cylinder shall incorporate a listed OPD 

(overfill protection device).  Do not store a spare LP-gas cylinder under or near this appliance. Never fill the 

cylinder beyond 80 percent full.  If the preceding information is not followed exactly, a fire causing death 

or serious injury may occur.

BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and 

piping should be located as shown in the built-in instructions.  A flexible metal connector is included to 

simplify the installation of the unit.  Connect this flexible metal connector to the flare fitting on the end of 

the manifold.  Connect the other end of the connector to the gas piping.  Ensure that the connector does 

not pass through a wall, floor, ceiling or partition, and is protected from damage.  Do not use a hose to 

connect the unit except to connect the cylinder regulator to the piping system.  It must be connected with 

rigid pipe, copper tube or an approved flexible metal connector which complies with Z21.4 /CSA 6.10.  
The installation must comply with CAN B149.1 Natural Gas and Propane installation code in Canada, or to 

the National Fuel Gas code, ANSI Z223.1 in the United States.  The gas supply pipe must be sufficiently sized 

to supply the BTU/h specified on the rating plate, based on the length of the piping run.  If installing a side