BlueStar RGTNB304BV2 Manuel
16
OPERATION
OPEN TOP BURNERS
Start-Up
Remove the ring grates and top grates and thoroughly wash them with hot, soapy water, rinse, and dry
immediately. Extended exposure to moisture may cause rusting of exposed metal surfaces. Each top grate
section has four leveling screws, which may be used to level your grates.
Operation
immediately. Extended exposure to moisture may cause rusting of exposed metal surfaces. Each top grate
section has four leveling screws, which may be used to level your grates.
Operation
To light an open top burner, push, then turn the appropriate control knob to the "HIGH" position. This
control is both a gas valve and an electric switch. When the knob is placed in the "HIGH" position, which
is required for lighting all burners, gas is permitted to flow to the burner, and the igniter will begin sparking
with a "clicking" sound. If you do not hear this sound, turn the control knob to the "OFF" position and
check to make sure that the unit is plugged in and that the fuse or circuit breaker on the service line is not
blown or tripped. It is possible that multiple igniters will spark. Any additional troubleshooting of unit will
require an authorized service technician.
control is both a gas valve and an electric switch. When the knob is placed in the "HIGH" position, which
is required for lighting all burners, gas is permitted to flow to the burner, and the igniter will begin sparking
with a "clicking" sound. If you do not hear this sound, turn the control knob to the "OFF" position and
check to make sure that the unit is plugged in and that the fuse or circuit breaker on the service line is not
blown or tripped. It is possible that multiple igniters will spark. Any additional troubleshooting of unit will
require an authorized service technician.
NOTE: Do not operate this unit between
“high” and “off”! If the flame extinguishes, re-
ignition will not occur and gas will leak.
“high” and “off”! If the flame extinguishes, re-
ignition will not occur and gas will leak.
After a few seconds of sparking, enough gas will
have traveled through the burner to achieve ignition.
There is no pilot burner. The igniter lights the burner
directly.
After the burner lights, set the burner control knob to any position between the "HIGH" and "LOW" settings
to adjust the flame height to your desired cooking specifications. All open top burners are equipped with
automatic re-ignition, which will re-light the burner if it goes out for any reason.
have traveled through the burner to achieve ignition.
There is no pilot burner. The igniter lights the burner
directly.
After the burner lights, set the burner control knob to any position between the "HIGH" and "LOW" settings
to adjust the flame height to your desired cooking specifications. All open top burners are equipped with
automatic re-ignition, which will re-light the burner if it goes out for any reason.
1/2"
Clean-Up
The ring grates and top grates on your unit are coated with a porcelain enamel that may be effectively
cleaned with hot soapy water.
cleaned with hot soapy water.
In the event that heavy soiling occurs, a commercial oven cleaner may be used on these parts. Be sure to
follow the manufacturer's instructions carefully, and to avoid the cleaner coming in contact with the
painted surfaces of your unit.
follow the manufacturer's instructions carefully, and to avoid the cleaner coming in contact with the
painted surfaces of your unit.
REMEMBER: To assure proper fit, replace top and ring grates in their original positions!
NOTE: All burners, including the
simmer burner, must be ignited in
the “HIGH” position. When set on
"HIGH," the flames on the open top
burners should be approximately
1/2 inch high and burn with a sharp
blue tip. Some yellow may occur,
depending on the gas type being
supplied.
simmer burner, must be ignited in
the “HIGH” position. When set on
"HIGH," the flames on the open top
burners should be approximately
1/2 inch high and burn with a sharp
blue tip. Some yellow may occur,
depending on the gas type being
supplied.