Thermador PRG486GDH Manuel De Montage

English 2

To avoid possible burn or fire hazard, a 

backguard designed specifically for this range 

must be installed whenever the range is used.

•

A backguard must be utilized when there is less than a 

12" horizontal clearance between combustible 

materials and the back edge of the range. A 

Thermador backguard must be ordered separately and 

installed at the rear of the range. A Low Back is 

supplied with the 30“ model, and all other models are 

supplied with a Flush Island Trim. For island 

installations and other installations with more than 12" 

clearance, an optional stainless steel Island Trim is 

available to cover the backguard mounting flanges.

•

Verify that the appliance is correct for the type of gas 

being provided. Refer to Step 5 on page

 

11 before 

proceeding with the installation.

To eliminate risk of burns or fire caused by 

reaching over heated surface units, cabinet 

storage located above the surface units should 

be avoided.

Gas Supply:
Natural Gas — 6 inch water column. (14.9 mb) min., 14 

inch (34.9 mb) maximum
Propane Gas — 11 inch water column. (27.4 mb) min., 14 

inch (34.9 mb) maximum 
Electric Power Supply: 
30" Model: 

4 Burners — 120 VAC, 60 Hz., 1Ph., 10 Amp circuit.
36" Models: 

6 Burners — 120 VAC, 60 Hz., 1Ph., 10 Amp circuit 

4 Burners with Griddle — 120 VAC, 60 Hz., 1Ph., 20 Amp 

circuit.
48" Models: 

6 Burners with Griddle — 120 VAC, 60 Hz., 1Ph., 20 Amp 

circuit.

CAUTION:
When connecting the unit to propane gas, make 

certain the propane gas tank is equipped with its 

own high-pressure regulator in addition to the 

pressure regulator supplied with the range.

This unit is designed as a cooking appliance. 

Based on safety considerations, never use it for 

warming or heating a room.

This appliance has been tested in accordance with ANSI 

Z21.1, Standard for Household Cooking Appliances (USA) 

and in accordance with CAN 1.1-M81 Domestic Gas 

Ranges (Canadian). It is strongly recommended that this 

appliance be installed in conjunction with a suitable 

overhead vent hood. (See Step 1 for Ventilation 

Requirements.) Due to the high heat capability of this unit, 

particular attention should be paid to the hood and duct 

work installation to assure it meets local building codes. 

This appliance complies with one or more of the following 

standards: 
•

UL 858, Standard for the Safety of Household Electric 

Ranges 

•

UL 923, Standard for the Safety of Microwave Cooking 

Appliances 

•

UL 507, Standard for the Safety of Electric Fans 

•

ANSI Z21.1, American National Standard for 

Household Cooking Gas Appliances 

•

CAN/CSA-C22.2 No. 113-08 Fans and Ventilators 

•

CAN/CSA-C22.2 No. 61-08 Household Cooking 

Ranges 

Check local building codes for the proper method of 

appliance installation. Local codes vary. Installation, 

electrical connections and grounding must comply with all 

applicable codes. In the absence of local codes the 

appliance should be installed in accordance with the 

National Fuel Gas Code ANSI Z223.1/ NFPA 54 current 

issue and National Electrical Code ANSI/NFPA 70 -current 

issue. In Canada, installation must be in accordance with 

the CAN 1-B149.1 and .2 – Installation Codes for Gas 

Burning Appliances and/or local codes. 

It is the responsibility of the owner and the installer to 

determine if additional requirements and/or standards 

apply to specific installations.