Summit SCR312L Manuel Du Propriétaire
![Summit](https://files.manualsbrain.com/attachments/4595b4104c7fa9afd97f50cce9de2cb70cbe780f/common/fit/150/50/6713795c9069b8d69615243bf026a42be787dcf338c28695e911d49078e6/brand_logo.png)
Page 8 SUMMIT APPLIANCE
SCR312L CONTROL PANEL
▼
LED ON/OFF
Set °C/°F Set
Display Light Switch Temp Switch Temp
UP key combination DOWN
UP key combination DOWN
The Light Switch allows you to turn on the interior light with a push
of the button. The light will stay on until you push the button again,
so be sure to shut it off when not needed, to save energy and
avoid raising the cabinet temperature unnecessarily.
The LED Display normally shows the current average temperature
inside the cabinet. It also allows you to set the temperature you
desire, as described below.
The two SET buttons let you raise or lower the cabinet
temperature to the level you prefer. To change the temperature,
press one of the SET buttons. The LED Display will begin to blink,
and while it is blinking, raise or lower the displayed temperature by
pressing the appropriate SET button. Stop when the Display
shows the temperature you want. In a couple of seconds, the
Display will stop blinking and the unit will adjust itself to the new
temperature.
NOTE: You cannot change the set temperature unless the Display
is blinking.
The °C/°F switch is a combination of keys. If you press both ▲
and ▼ buttons together and hold them for three seconds, the
temperature readout will change between Fahrenheit and Celsius.
of the button. The light will stay on until you push the button again,
so be sure to shut it off when not needed, to save energy and
avoid raising the cabinet temperature unnecessarily.
The LED Display normally shows the current average temperature
inside the cabinet. It also allows you to set the temperature you
desire, as described below.
The two SET buttons let you raise or lower the cabinet
temperature to the level you prefer. To change the temperature,
press one of the SET buttons. The LED Display will begin to blink,
and while it is blinking, raise or lower the displayed temperature by
pressing the appropriate SET button. Stop when the Display
shows the temperature you want. In a couple of seconds, the
Display will stop blinking and the unit will adjust itself to the new
temperature.
NOTE: You cannot change the set temperature unless the Display
is blinking.
The °C/°F switch is a combination of keys. If you press both ▲
and ▼ buttons together and hold them for three seconds, the
temperature readout will change between Fahrenheit and Celsius.
▲
SUMMIT APPLIANCE Page 5
appliance straight out when moving it. Do not wiggle or “walk”
the appliance when trying to move it, because floor damage
can occur.
the appliance when trying to move it, because floor damage
can occur.
5. Clean Before Using:
After you remove all of the packaging materials, clean the
inside of your appliance before using it. See cleaning
instructions in the Cleaning and Maintenance section of this
manual.
inside of your appliance before using it. See cleaning
instructions in the Cleaning and Maintenance section of this
manual.
6. The appliance has leveling legs at the front. For best
operation, be sure the unit is level.
Keep flammable materials and vapors such as gasoline away from
appliances. Failure to do so can result in fire or explosion.
LOCATION REQUIREMENTS
IMPORTANT: Do not install the appliance near an oven, radiator
or other heat source, nor in a location where the temperature will
fall below 45°F (7°C). Do not place in direct sunlight.
Check the strength of the floor before installing the appliance. It
should hold the weight of a fully loaded appliance. Allow at least
1” (2.5 cm) of airspace at the top and on both sides of the
appliance and 1” (2.5 cm) between the back of the appliance and
the wall. If the appliance is going to be placed beside a wall, if
possible, leave extra space on the hinge side so the door can
open wider than its width (to make it easier to remove shelves or
storage bins.)
Choosing the Right Place
Place the unit in a dry and regularly ventilated place. It is
recommended that this appliance always be operated in an
ambient temperature of at least 32°F and under 90°F. The
appliance may be exposed to lower or higher temperatures but
only for a short period of time. Never place the appliance near
heat-emitting devices (e.g., oven, radiator, water heater or similar
devices) or in moist areas, and do not expose it to direct sunlight.
Recommended Grounding Method
A 115V, 60Hz AC-only, grounded electrical supply, including a 15-
or 20-amp fuse or circuit breaker, is required. It is recommended
that a separate circuit serving only your appliance be provided.
Use outlets that cannot be turned off by a switch or pull chain.
Connect this appliance to a 3-prong power supply socket (which
has a good ground terminal). If you only have a two-prong outlet,