Crossover DAWF0EM Manuel Du Propriétaire

10

Laundrylux

112999-1

PL12 – Amount To Start (AtSt)

This program sets the “Amount To Start” the dryer and can be

programmed from a minimum of 1 to a maximum of 9999.

PL13 – Minimum Amount

For Additional Time (AFAt)

This program need only be set when the Phase 5

microprocessor controller (computer) is set in the

“Accumulative Coin” (“ACOn”) mode (PL01).   The value set

for this program is what will have to be inserted for more time

after the “Amount To Start” (“AtSt”) has been inserted.
Example No. 1: “Amount to Start” (“AtSt”) is 50¢ for 30 minutes

and an additional 50¢ is required for more time.  In this example

PL13 should be set for 50¢.

PL14 – Maximum Time

For Automatic Dry (Adrt)

This program is used only when the Phase 5 microprocessor

controller (computer) is set in the  Automatic Mode.   This

program controls the maximum time the dryer will run even if

the Dryness Level program (PL02) has not been reached.

PL15 – Anti-Wrinkle Timing

Guard Delay Time (GdLY)
This program controls the dwell (stop) time and activation of

anti-wrinkle “Guard On Time” (“Gont”).  The dwell (stop) time

can be programmed from a minimum of 1 minute to a maximum

of 9 minutes in 1 minute increments.

Guard On Time (Gont)
The setting controls the amount of time that the tumbler will

turn, without heat, when the Anti-Wrinkle is active (“Grd”).  The

“Guard On Time” (“Gont”) is programmable from a minimum

of 1-second to a maximum of 99-seconds in 1-second

increments.

PL16 – Active Guard Time (AGt)

This program controls the maximum time that the Anti-Wrinkle

Program will be active and is programmable from a minimum

of 1 minute to a maximum of 99 minutes in 1 minute

increments.

PL17 – “A” and “b” Factors

This location will include the “Auto-Cycle” parameters.  These

parameters are necessary to allow the Phase 5 microprocessor

controller (computer) to calculate the percent age of dryness

in the tumbler.  The “A” Factor is adjustable from 1 to 99.
These p arameters are the factors that the Phase 5

microprocessor controller (computer) utilizes when

programmed for an “Automatic Drying Cycle.”  The “A” Factor

slope program, pertains to the thermal characteristic of each

model dryer.  The “b” Factor, heat loss (offset) program, also

pertains to the thermal characteristics of each model dryer .

This factor setting is dependent upon the model dryer and

type of heating unit.
The “A” and “b” Factors have not been preprogrammed by

the factory and must be programmed if the Phase 5

microprocessor controller (computer) programming is changed

to be used in the  Automatic Mode.   The “A” and “b” Factors

must be programmed for the particular dryer model and heating

unit as shown in the “A” and “b” Factors (parameter) table on

page 37 of this manual.

Programming Instructions ___________

Introduction To Programming

The various program (parameters) dryer selections are stored

in the computer memory and are cataloged as “PL” 1 through

17.  These programs (parameters) have been preprogrammed

by the factory as noted on page 36 of this manual.  The various

program selections available are outlined in the proceeding

section (Program Selection on page 6).
All programming is done through the keypad selection buttons

on the front of the control p anel.   To change programs

(parameters) or to put the Phase 5 microprocessor controller

(computer) in the temperature display mode or the coin count

display mode, the PS located on the back side of the

microprocessor controller (computer) must be put into the

(down) position (PSC).  Note: on DA WS0 dryers with the

controls on the bottom, the lint door sensor switch must be

temporarily pushed in while flipping the PS toggle switch down.

Failure to do so will prevent the controller from entering into

programming mode.
First make sure there is no cycle in progress and the L.E.D.

display reads “FILL” and/or “Amount To Start,” or “FILL” and/

or “FrEE.”  Close the Program Switch (PSC).   The L.E.D.

display will now read the temperature in the dryer (i.e., 72° F

[22° C]).  From this point, any of the 17 program locations can

be accessed by pressing the “PERM PRESS” key once, at

which time the L.E.D. display will read “PL01.”
To alter programming, the operator must first locate the

program location or parameter to be changed.  To advance to

the specific program location press the “HI  TEMP” key until

the desired program location is displayed (i.e. PL01, PL02,

etc.).  The “LO TEMP” key will advance the program locations

downward (i.e., PL11, PL10, etc.).  Once the correct program

location is displayed and access to change is desired, press

the “PERM PRESS” key.  The “PERM PRESS” key provides

two functions:
Allows access into a PL.
Advances to next bit (p art of a program location) or next

location.