Maytag UXD86DYS Illustrations
A. Downdraft vent
B. Cooktop
B. Cooktop
C. Measurement of cooktop rear
overhang.
D. D = Measurement of cooktop rear
overhang (C) + 1
¹³⁄₁₆" [46.2 mm] (E)
E. 1
¹³⁄₁₆" (46.2 mm)
F. ½" (12.7 mm) minimum
G. ¼" (6.4 mm) minimum
H. Countertop and backsplash
H. Countertop and backsplash
I. ½" (12.7 mm) minimum
A
B
C
E
H
D
I
G
F
30" (76.2 cm) and 36" (91.4 cm) Retractable (Pop-Up) Downdraft Vent System
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Instructions packed with product. Specifications subject to change without notice.
Ref. W10342491C
2/8/2012
Page 1 of 3
COUNTERTOP CUTOUT DIMENSIONS
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
UXD8630DY
UXD8636DY
Electrical
A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is required.
Top trim widths:
30" (76.2 cm)
36" (91.4 cm)
30" (76.2 cm)
36" (91.4 cm)
13¹⁄₂
" (34.3 cm)
retractable
vent height
vent height
27" (68.6 cm) for 30" (76.2 cm) vent
33" (83.8 cm) for 36" (91.4 cm) vent
33" (83.8 cm) for 36" (91.4 cm) vent
16
¹⁄₂
" (42.0 cm)
10"
(25.4 cm)
2
¹⁄₈
" (5.4 cm)
28
¹⁄₂
"
(72.4 cm)
³⁄₈
" (0.95 cm)
1
¹⁄₂
" (3.8 cm)
13
¹⁄₈
" (33.4 cm)
5
¹⁄₄
"(13.3 cm)
for 30" (76.2 cm) vent
8
8
¹⁄₄
"(21.0 cm)
for 36" (91.4 cm) vent
³⁄₄
(1.9 cm)
LOCATION REQUIREMENTS
NOTE:
Downdraft vent is installed directly behind the cooktop. Install the
downdraft vent first, then install the cooktop.
IMPORTANT:
Observe all governing codes and ordinances.
●
Have a qualified technician install the downdraft vent. It is the installer’s
responsibility to comply with installation clearances specified on the
model/serial rating plate. The model/serial rating plate is located on the front of
the downdraft vent above the terminal box cover.
●
Downdraft vent location should be away from strong draft areas, such as
windows, doors, and strong heating vents or fans.
●
Cabinet opening dimensions that are shown must be used. Given dimensions
provide minimum clearance.
●
Consult the cooktop manufacturer installation instructions before making any
cutouts.
Check that the downdraft vent and cooktop location will clear the
cabinet walls, backsplash, and rear wall studs inside the cabinet.
Check for the minimum distance between the front edge of the
Check for the minimum distance between the front edge of the
countertop and the front edge of the cooktop. The minimum horizontal
distance between the overhead cabinets is the same as the width of the
installed downdraft vent.
●
All openings in ceiling and wall where the downdraft vent will be installed must
be sealed.
●
Grounded electrical outlet is required. See “Electrical Requirements” section.
●
When installing the downdraft vent, the cabinet drawer will need to be removed
and the drawer front installed permanently to the cabinet.
Cabinet Construction:
Downdraft vent is designed for use in a cabinet with a depth of 24" (61 cm).
Some installations require a countertop deeper than 25" (63.5 cm). See the
Countertop Cutout Dimensions section.
The maximum depth of the overhead cabinet is 13" (33 cm). Overhead cabinets
The maximum depth of the overhead cabinet is 13" (33 cm). Overhead cabinets
installed at either side of the downdraft vent must be 18" (45.7 cm) above the
cooking surface.
For Mobile Home Installations
The installation of this range hood must conform to the Manufactured Home
Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal
Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or
when such standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI
A225.1/NFPA 501A*, or latest edition, or with local codes.
A=
¹⁄₂
" (12.7 mm)
minimum
21
⁵⁄₁₆
"
(54.1 cm)
Cutouts are
for 3
for 3
¹⁄₄
" x 10"
(8.3 x 25.4 cm)
rectangular or 6"
(15.2 cm) round
vent system.
rectangular or 6"
(15.2 cm) round
vent system.
Centerline of cooktop cutout
21⁵⁄₁₆
"
(54.1 cm)
Locate power
supply junction
box at lower
left hand
rear corner
of the cabinet.
supply junction
box at lower
left hand
rear corner
of the cabinet.
10
" (25.4 cm)
NOTES:
●
See cooktop manufacturer’s instructions for cooktop cutout depth and width.
●
Use dimensions for vent system cutout location that applies to your
installation.
●
Interior mounted blower systems connect with 3
¹⁄₄" x 10" (8.3 x 25.4 cm)
rectangular or 6" (15.2 cm) round vent system. The cutout locations for this
vent system will depend on your specific installation.
CABINET DIMENSIONS
IMPORTANT:
Countertops with a bull-nosed front edge are not
recommended for these installations.
●
Some models require a countertop deeper than 25" (63.5 cm); see
the following Countertop Cutout Dimensions section.
the following Countertop Cutout Dimensions section.
●
To avoid mistakes, it is recommended that the cooktop and vent
cutouts be drawn on the countertop before making any cutouts.
cutouts be drawn on the countertop before making any cutouts.
●
See Cooktop Installation Instructions for complete cutout
dimensions, location dimensions and installation details.
dimensions, location dimensions and installation details.