Frigidaire FPEH3077RF-SS Manuel Du Propriétaire
9
BEFORE SETTING SURFACE CONTROLS
About the Ceramic Glass Cooktop
The ceramic cooktop has radiant surface elements located
below the surface of the glass. The design of the ceramic
cooktop outlines the area of the surface element under-
neath. Be sure to match the pan size with the diameter of
the element outline on the cooktop and only flat-bottomed
cookware should be used.
below the surface of the glass. The design of the ceramic
cooktop outlines the area of the surface element under-
neath. Be sure to match the pan size with the diameter of
the element outline on the cooktop and only flat-bottomed
cookware should be used.
The type and size of cookware, the number of surface
elements in use and their settings are all factors that will
affect the amount of heat that will spread to areas beyond
the surface elements. The areas surrounding the elements
may become hot enough to cause burns.
elements in use and their settings are all factors that will
affect the amount of heat that will spread to areas beyond
the surface elements. The areas surrounding the elements
may become hot enough to cause burns.
About the Radiant Surface Elements
The element temperature rises gradually and evenly. As the
temperature rises, the element will glow red. To maintain
the selected setting the element will cycle on and off. The
heating element retains enough heat to provide a uniform
and consistent heat during the off cycle.
temperature rises, the element will glow red. To maintain
the selected setting the element will cycle on and off. The
heating element retains enough heat to provide a uniform
and consistent heat during the off cycle.
For efficient cooking, turn off the element several minutes
before cooking is complete. This will allow residual heat to
complete the cooking process.
before cooking is complete. This will allow residual heat to
complete the cooking process.
The cooktop should not be used as a cutting board or
work surface. Dropping heavy or hard objects on the
cooktop may crack it.
work surface. Dropping heavy or hard objects on the
cooktop may crack it.
Pans with rough bottoms may scratch the cooktop
surface. Placing food directly on the smoothtop surface
(without cooking utensil) is not recommended as difficult
cleaning will result and foods may smoke and cause
potential fire hazard.
surface. Placing food directly on the smoothtop surface
(without cooking utensil) is not recommended as difficult
cleaning will result and foods may smoke and cause
potential fire hazard.
Always lift cookware before moving on ceramic glass
cooktop. Any cookware that has rough or dirty bottoms
can scratch the ceramic cooktop. Always start with clean
cookware.
cooktop. Any cookware that has rough or dirty bottoms
can scratch the ceramic cooktop. Always start with clean
cookware.
IMPORTANT
Do not allow aluminum foil, or any material that can melt,
to make contact with the ceramic glass cooktop. If these
items melt on the cooktop, they will damage the ceramic
cooktop.
to make contact with the ceramic glass cooktop. If these
items melt on the cooktop, they will damage the ceramic
cooktop.
•
Radiant elements have a limiter that allows the
element to cycle on and off, even at the HI setting.
This helps to prevent damage to the ceramic smooth
top. Cycling at the HI setting is normal and can occur
if the cookware is too small for the radiant element or
if the cookware bottom is not flat.
element to cycle on and off, even at the HI setting.
This helps to prevent damage to the ceramic smooth
top. Cycling at the HI setting is normal and can occur
if the cookware is too small for the radiant element or
if the cookware bottom is not flat.
•
Be sure to read detailed instructions for ceramic glass
cooktop cleaning in the General Care & Cleaning
section and Before You Call checklist section of this
Use and Care Guide.
cooktop cleaning in the General Care & Cleaning
section and Before You Call checklist section of this
Use and Care Guide.
•
The element on and hot surface indicator lights will
glow when the element is turned on and will continue
to glow after the control knob is turned to the OFF
position. It will glow until the heating surface area has
cooled sufficiently. The glass surface may still be hot
and burns may occur if the glass surface is touched
before the indicator light has turned off.
glow when the element is turned on and will continue
to glow after the control knob is turned to the OFF
position. It will glow until the heating surface area has
cooled sufficiently. The glass surface may still be hot
and burns may occur if the glass surface is touched
before the indicator light has turned off.
CAUTION
NOTE