HP BladeSystem c7000 enclosure + 4 x ProLiant BL460c G6 507014-B21-BUN1 Manuel D’Utilisation

Codes de produits
507014-B21-BUN1
Page de 35
Dynamic Power Capping
Dynamic Power Capping
Dynamic Power Capping
Dynamic Power Capping HP Dynamic Power Capping is the industry's first and only power capping solution that lets you reclaim
trapped power and cooling capacity without putting electrical infrastructure or server performance at
risk. The enclosure Dynamic Power Cap will be shared amongst all of the installed devices and
individual server caps will be changed to match the server load. This will optimize the performance of the
servers while ensuring that the enclosure stays below the cap value. Dynamic Power Capping solution is
available only through the HP Insight Control management software.
Rack Airflow
Rack Airflow
Rack Airflow
Rack Airflow
Requirements
Requirements
Requirements
Requirements
Rack 10000 G2 series cabinets
Rack 10000 G2 series cabinets
Rack 10000 G2 series cabinets
Rack 10000 G2 series cabinets
The increasing power of new high-performance processor technology requires increased cooling
efficiency for rack-mounted servers. The G2 10000 Series Racks provide enhanced airflow for maximum
cooling, allowing these racks to be fully loaded with servers using the latest processors.
NOTE: 
NOTE: 
NOTE: 
NOTE: For operation with the DC Input Module the G2 1000 Series Rack Extension is required to allow
DC Power Cabling to be installed.
CAUTION:
CAUTION:
CAUTION:
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure
adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and rear doors, you must
allow 830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit
adequate airflow (equivalent to the required 64 percent open area for ventilation).
The clearance from face of rack to inside of the front door needs to be 1.75" minimum.
Side: The clearance between the installed rack component and the side panels of the rack must be
a minimum of 2.75 inches (7 cm).
Depth: Minimum 39.4 inches (1000mm) for AC power, 47 inches (1200mm) for DC Power Input
Adjustable rack rails are shipped with each enclosure:
Minimum rail length: 25 inches (635mm)
Maximum rail length: 34 inches (864mm)
CAUTION:
CAUTION:
CAUTION:
CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This
arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling
that can lead to thermal damage.
Factory Express Portfolio
Factory Express Portfolio
Factory Express Portfolio
Factory Express Portfolio
for Servers and Storage
for Servers and Storage
for Servers and Storage
for Servers and Storage
HP Factory Express offers configuration, customization, integration and deployment services for HP
servers and storage products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading, asset
tagging and custom packaging. HP products supported through Factory Express include: a wide array of
servers and storage: HP Integrity, HP ProLiant & HP ProLiant & Integrity Server Blades, HP BladeSystem,
HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable
network switches.
For more information on Factory Express services for your specific server model please contact your sales
representative or go to: 
QuickSpecs
HP BladeSystem c7000 Enclosure
HP BladeSystem c7000 Enclosure
HP BladeSystem c7000 Enclosure
HP BladeSystem c7000 Enclosure
HP BladeSystem c-Class Overview
DA - 12810   Worldwide — Version 18 — November 16, 2009
Page 5