Amana AMV2175CB Guide D’Installation Rapide

The microwave oven must be installed on a minimum of 1 wall 
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
1. Using measuring tape, find and clearly mark the vertical 

centerline of the opening.

2. Align the center markers on the cardboard template to the 

centerline on the wall, making sure it is level, and that the top 
of the cardboard template is butted up against the bottom 
edge of the upper cabinet.

■

If the front edge of the upper cabinet is lower than the back 
edge, lower the cardboard template so that its top is level with 
the front edge of the cabinet.

■

If the cardboard template is damaged or unusable, measure 
and mark the wall with the dimensions described in Step 4.

3. Holding the cardboard template in place, mark both holes in 

the lower corners, and draw a horizontal line across the 
bottom edge of the cardboard template. These represent the 
mounting plate’s end holes and bottom edge.

4. Remove the cardboard template and check the markings:

■

The bottom edge line must be 17

¹⁄₄" (43.8 cm) from the 

bottom of the upper cabinet, and must be level.

■

The end holes must be 15

³⁄₄" (40.0 cm) from the bottom 

edge of the upper cabinet, and must be on a level line with 
each other. They must each be 14

¹⁄₈" (35.9 cm) from the 

centerline.

5. With the support tabs facing forward (see illustrations in 

“Locate Wall Stud(s)” section), align the mounting plate center 
markers to the centerline on the wall, making sure its bottom 
edge is aligned to the horizontal line drawn in Step 3, and that 
the end holes are properly marked. Make sure the mounting 
plate is level.

6. Holding the mounting plate in place, find the wall stud 

centerline(s) drawn in Step 2 of “Locate Wall Stud(s),” and 
mark at least 1, preferably 2 hole(s) through the mounting 
plate, closest to the wall stud centerline(s). See figures 1, 2 
and/or 3 in “Possible Wall Stud Configurations” in “Locate 
Wall Stud(s)” section. The blackened holes in the shaded 
areas are ideal hole locations.

7. Set the mounting plate aside.

8. Mark the centerline 3/8" (1 cm) down from the bottom edge of 

the upper cabinet.

9. Using measuring tape, measure out 6" (15.2 cm) on both sides 

of the centerline, and mark.

10. Measure down 4" (10.2 cm) from the mark made in Step 8, 

and mark.

11. Using a straightedge, draw the 2 horizontal, level lines through 

the marks made in steps 8 and 10.

12. Draw the 2 vertical, plumb lines down from the marks made in 

Step 9 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle. 
This is the venting cutout area.

13. Cut a 3/4" (19 mm) hole in one corner of the cutout area.
14. Using a keyhole saw, cut out the venting cutout area.

In addition to being installed on at least 1 wall stud, the mounting 
plate must attach to the wall at both end holes. If the end holes 
are not over wall studs, use two 1/4-20 x 3" round-head bolts with 
toggle nuts; if 1 end hole is over a wall stud, use 1 lag screw and 
one 1/4-20 x 3" round-head bolt with toggle nut; or if both end 
holes are over wall studs, use 2 lag screws. Following are 
3 installation configurations.

1. Drill 3/4" (19 mm) holes through the wall at both end holes 

marked in Step 3 of “Mark Rear Wall.”

2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s) 

marked in Step 6 of “Mark Rear Wall.” Refer to figures 1 and 2 
in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)” 
section.

A

A

C

B

D