Ryobi P700 Manuel D’Utilisation

Page de 14
4
5
SPECIFIC SAFETY RULES
 
n
   
Do not permit children to use worklight unsupervised. 
It is not a toy. The temperature of the bulb will become 
hot after being on for only a short period of time. This 
hot temperature can cause burn injury if touched and can 
create sufficient heat to melt some fabrics.
n
   
Stay alert. Watch what you are doing and use common 
sense. Do not rush.
n
 
If wrapped or in contact with fabrics, the worklight 
lens can produce sufficient heat to melt some fabrics.
 
To avoid serious personal injury, never allow the worklight 
lens to come in contact with anything.
n
   
Check damaged parts. Before further use of this work-
light, a part that is damaged should be carefully checked 
to  determine  that  it  will  operate  properly  and  perform 
its intended function. Do not use worklight if it does not 
function properly.
WARNING! 
READ AND UNDERSTAND ALL INSTRUCTIONS. Fail-
ure to follow all instructions listed below, may result in 
electric shock, fire and/or serious personal injury.
n
  Before using battery charger, read all instructions and 
cautionary markings in this manual, on battery charger, 
battery, and product using battery to prevent misuse of 
the products and possible injury or damage.
CAUTION:
To  reduce  the  risk  of  electric  shock  or  damage  to  the 
charger  and  battery,  charge  only  nickel-cadmium  re-
chargeable batteries as specifically designated on your 
charger.  Other  types  of  batteries  may  burst,  causing 
personal injury or damage.
n
  
Do  not  use  charger  outdoors  or  expose  to  wet  or 
damp conditions. Water entering charger will increase 
the risk of electric shock.
n
  
Use of an attachment not recommended or sold by the 
battery charger manufacturer may result in a risk of 
fire, electric shock, or injury to persons. Following this 
rule will reduce the risk of electric shock, fire, or serious 
personal injury.
 
n
  
Do not abuse cord or charger. Never use the cord to 
carry the charger. Do not pull the charger cord rather than 
the plug when disconnecting from receptacle. Damage 
to the cord or charger could occur and create an electric 
shock hazard. Replace damaged cords immediately.
n
  
Make sure cord is located so that it will not be stepped 
on, tripped over, come in contact with sharp edges 
or moving parts or otherwise subjected to damage or 
stress. This will reduce the risk of accidental falls, which 
could cause injury, and damage to the cord, which could 
result in electric shock.
n
  
Keep  cord  and  charger  from  heat  to  prevent
damage to housing or internal parts.
n
  
Do not let gasoline, oils, petroleum-based products, 
etc. come in contact with plastic parts. They contain 
chemicals that can damage, weaken, or destroy plastic.   
n
  
An  extension  cord  should  not  be  used  unless
absolutely  necessary.  
Use  of  improper  extension 
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
  a.  That  pins  on  plug  of  extension  cord  are  the
 
same  number,  size  and  shape  as  those  of
 
plug on charger.
  b.  That  extension  cord  is  properly  wired  and  in
 
good electrical condition; and
  c.  That  wire  size  is  large  enough  for  AC  ampere
 
rating of charger as specified below: 
   
Cord Length (Feet) 
25´ 
50´ 
100´
   
Cord Size (AWG) 
16 
16 
16
   
NOTE: AWG = American Wire Gauge
n
  
Do  not  operate  charger  with  a  damaged  cord  or 
plug, 
which could cause shorting and electric shock. If 
damaged, have the charger replaced by an authorized 
serviceman.
n
  
Do not operate charger if it has received a sharp blow, 
been dropped, or otherwise damaged in any way. 
Take it 
to an authorized serviceman for electrical check to determine 
if the charger is in good working order. 
n
  
Do not disassemble charger. Take it to an authorized 
serviceman when service or repair is required. Incorrect 
reassembly may result in a risk of electric shock or fire.
n
  
Unplug  charger  from  outlet  before  attempting 
any  maintenance  or  cleaning  to  reduce  the  risk  of
electric shock.
n
  
Disconnect  charger  from  the  power  supply  when 
not in use. 
This will reduce the risk of electric shock or 
damage to the charger if metal items should fall into the 
opening. It also will help prevent damage to the charger 
during a power surge.
Risk of electric shock. Do not touch uninsulated portion 
of output connector or uninsulated battery terminal.
n
  
Save these instructions. Refer to them frequently and 
use them to instruct others who may use this worklight. If 
you loan someone this worklight, loan them these instruc-
tions also to prevent misuse of the product and possible 
injury.
SAFETY RULES FOR CHARGER