Magnavox 39ME412V Manuel D’Utilisation

English

12

Initial setup

This section will guide you through the unit’s initial setting which 

includes selecting a language for your on-screen menu and autoprogram, 

which automatically scans and memorizes viewable channels.

Make sure the unit is connected to antenna or cable.

1

  After making all the necessary connections, press   to Turn On the 

unit.
•  It may take a few moments to Turn On the unit for the first time.
•  Initial setup menu appears automatically after the unit is Turned 

On.

2

  Use ▲▼ to select the on-screen language from the choices 

(English / Español / Français) on the right side of the TV screen, then 

press OK.

3

  Use ▲▼ to select Antenna for TV channels or Cable for CATV 

channels, then press OK.

Initial setup

Make sure the antenna is connected to ‘’ANTENNA IN’’ jack.

Select your signal source.

Antenna

Cable

Antenna

Cable

Or

ANTENNA IN

Skip

Select

OK

Back

Skip

 

– When Antenna is selected, the TV detects antenna signals. It 

searches for DTV and Analog TV channels available in your area.

 

– When Cable is selected, the TV detects signals supplied by cable. It 

searches for DTV, Analog TV and Cable channels available in your 

area.

•  Autoprogram will begin.

Initial setup

Please wait while the system is scanning for channels.

Auto programming may take more than 20 minutes to

complete.

0 ch

Skip

4

  Use ▲▼ to select the desired location setting, then press OK.

 

Home is ENERGY STAR

®

 qualified setting.

Initial setup

Location Home is recommended for normal home use

and is ENERGY STAR qualified.

In the Retail Store mode, all settings are fixed.

Retail

Home

Select

OK

•  Select Retail, the unit will be set up with predefined setting 

for retail displays. In this setting, the power consumption may 

possibly exceed the limited requirement of the ENERGY STAR

®

 

qualification.

•  Select Home, the unit is set to maximize the energy efficiency 

for home setting and it can be adjusted through a choice of 

picture and sound quality according to your preference. Use this 

setting to remove the E-sticker if visible from the display. 

➠

•  When the initial setup is completed, the lowest memorized 

channel with the confirmation message of the location setting 

will be displayed on the TV screen.

•  You must set Home in step 4. Otherwise, Picture and Sound 

settings you adjusted will not be memorized after the unit goes 

into Standby mode.

Note

 

•

 If you are not receiving a signal from your cable service, contact the Cable provider.

 

•

If you press   or MENU during autoprogram, this setup of TV channels will be 

canceled.

 

•

The initial autoprogram function can be executed for either Antenna or Cable only 

once. When you change the connection (Antenna / Cable), set Autoprogram again.

➠

 

•

If there is no signal Input from the antenna terminal and no operation for several 

seconds after you Turn On the unit, helpful hints appears. Follow the instructions listed 

on the TV screen.

Initial setup

No channel is registered.

Try Autoprogram again?

Verify that you have a cable connected to the “ANTENNA IN” jack

on the back of the TV, the channel installation process

searches this connection. If you are using a cable or satellite

box, please confirm the input which you have connected to

the box and press “SOURCE” key on the remote control to

select the appropriate source input.

Retry

Later

Select

OK

Skip

•  If you want to scan the channels automatically again.

 

  Autoprogram

➠

p. 19

•  You can add the desired cable and Analog channels 

unmemorized by autoprogram.

 

  Add channels

➠

p. 20

•  If you want to change to another language.

 

  Language    

➠

p. 26

•  If you want to change the location setting.

 

  Location    

➠

p. 26