Samsung RS26WUNS Manuel D’Utilisation
34
INSTALLATION OF THE WATER DISPENSER LINE
Check the amount of water supplied to the ice tray.
1) To remove : Set the "Ice Type" switch to the Ice off position.
Lift up (
①) and pull out (➁) the icemaker bucket in the freezer.
To replace : When replacing the drawer, be sure to press it
firmly into place. If it does not go all the way back, remove it
and rotate the drive mechanism 1/4 turn. Then push the
drawer back again.
firmly into place. If it does not go all the way back, remove it
and rotate the drive mechanism 1/4 turn. Then push the
drawer back again.
2) Throw away the first few batches of ice to allow the water line
to clear.
Be sure nothing interferes with the sweep of the feeler arm.
When the bin fills to the level of the feeler arm, the icemaker
will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale and shrink.
Be sure nothing interferes with the sweep of the feeler arm.
When the bin fills to the level of the feeler arm, the icemaker
will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale and shrink.
3) Important Facts About Your Dispenser :
Do not add ice from trays or bags to the
storage bin. It may not crush or dispense
well.
Avoid overfilling glass with ice and use of
narrow or extra-tall glasses. Backed-up
ice can jam the chute or cause the door in
the chute to freeze shut. If ice is blocking
the chute, poke it through with a wooden spoon.
Beverages and foods should not be quick-chilled in the ice storage bin.
To keep dispensed ice from missing the glass, put the glass close to, but not touching, the dis-
penser opening.
Some crushed ice may be dispensed even though you selected CUBES. This happens occasion-
ally when a few cubes accidentally get directed to the crusher.
After crushed ice is dispensed, some water may drip from the chute.
storage bin. It may not crush or dispense
well.
Avoid overfilling glass with ice and use of
narrow or extra-tall glasses. Backed-up
ice can jam the chute or cause the door in
the chute to freeze shut. If ice is blocking
the chute, poke it through with a wooden spoon.
Beverages and foods should not be quick-chilled in the ice storage bin.
To keep dispensed ice from missing the glass, put the glass close to, but not touching, the dis-
penser opening.
Some crushed ice may be dispensed even though you selected CUBES. This happens occasion-
ally when a few cubes accidentally get directed to the crusher.
After crushed ice is dispensed, some water may drip from the chute.
4) Water Supply to the Icemaker :
The icemaker must be connected to a cold water line.
5) Start the Icemaker :
Set the "Ice Type" to the "Cubed Ice" or "Crushed Ice" position. The icemaker will not begin to
operate until it reachs its operating of 10.4°F( -12°C) or below. It will then begin operation auto-
matically if the "Ice Type" is in the "Cubed Ice" or "Crushed Ice" position.
operate until it reachs its operating of 10.4°F( -12°C) or below. It will then begin operation auto-
matically if the "Ice Type" is in the "Cubed Ice" or "Crushed Ice" position.
CHECK THE WATER LEVEL
Rotate
Drive
Mechanism
Mechanism
Feeler Arm
ICE MAKER
• If there is no water supply, turn off the icemaker to save energy.
• In lower water pressure conditions, the water valve may turn on up to 3 times to make sure
• In lower water pressure conditions, the water valve may turn on up to 3 times to make sure
enough water reaches the icemaker.
NOTE
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 34