Seiko Instruments V-64S Manuel D’Utilisation
Appendix Adjustment of bi-direction position
Appendix Adjustment of bi-direction position
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
12.
Adjust the bi-direction position of each head. Reading the result of [BIDIRECTION1],
[BIDIRECTION2] and [BIDIRECTION3] print, enter the value.
[BIDIRECTION2] and [BIDIRECTION3] print, enter the value.
Set the printer to the offline.
(Press the key.)
(Press the key.)
Press key twice to display ADJUST.
Press key and then key to display the
adjustment pattern.
adjustment pattern.
Press key to select [BIDIRECTION1].
Then, press key.
Then, press key.
* When adjusting [NORMAL2] print mode, select [BIDIRECTION2]
and adjusting [FINE DRAFT] print mode, select [BIDIRECTION3].
Enter the number of the pattern where two lines are
aligned most closely. For example, when setting the M
color Print head, in “-21” in the figure to the right, two lines
are separated and in “-8” two lines are aligned in one. So
“-8” is the correct value.
This Printer has preset bi-direction position adjustment values for
major media. Basically, the adjustment is not required. But, if you
notice the followings in the bi-directional print ([BIDIR]) shown in
page 21 of this Guide, print the bi-directional adjustment pattern
and set each of the Print head position correctly.
notice the followings in the bi-directional print ([BIDIR]) shown in
page 21 of this Guide, print the bi-directional adjustment pattern
and set each of the Print head position correctly.
- bleeding (in a single color or different colors)
- bleeding of sharp lines such as register marks (in a single color
- bleeding of sharp lines such as register marks (in a single color
or different colors)
- uneveness of mixed colors
* Transfer of the preset values are effective only when new media are registered by
Windows or when the existing media information is copied by panel operation.
Press key. Then, the adjustment pattern in
the figure shown below is printed.
the figure shown below is printed.
After selecting ADJUST MENU, press key to
display [BIDIR ADJ1 L].
display [BIDIR ADJ1 L].
Press key to move the cursor and change
the head color with , keys.
the head color with , keys.
Press key to decide the head color to be
corrected and make it ready for entering the
parameter.
corrected and make it ready for entering the
parameter.
In the [BIDIRECTION] patterns, enter the
numeral of pattern where two lines of each
color Print head are aligned in one.
numeral of pattern where two lines of each
color Print head are aligned in one.
Select the digit with , keys and change the value with
, keys.
, keys.
Press key.
Adjust [BIDIR ADJ1 R] using the same method.
Adjust other colors using the same method.
INK
MEDIA REG
MEDIA
M.ADV
-21
-8
Two lines
are
separated.
-32
-31
-30
-29
-28
-28
-32
0
+1
+2
+3
+4
+31
media adv
anc
e dir
e dir
ec
tion
Two lines
are aligned
in one.
PRINTER
SETUP
ADJUST
HEATER
#TEST PRINT
＊
NOZZLE PRINT
#BIDIR ADJ1 L XXXXXX
#Y >+00
#BIDIR ADJ1 L XXXXXX
#M >+00
#BIDIR ADJ1 L XXXXXX
#M *+00
#BIDIR ADJ1 L XXXXXX
#M >-08
#BIDIR ADJ1 L XXXXXX
#M >-08
#TEST PRINT
＊
BIDIREC TION1
#TEST PRINT
＊
EXECUTING
NG
OK