Toshiba TDP-D2 Manuel D’Utilisation
19
Operations
18
■ Connecting the power cord
1
Insert the power cord connector into the
AC IN socket of the projector.
2
Insert the power cord plug into a wall or
other power outlet.
■ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
turned on. If it is left on, it could become deformed due
to heat.
■ Turning the power on
1
Turn on the main power switch
Then, following three green indicators
will come on for several seconds: ON,
TEMP, and LAMP. Next, the ON
indicator will change to orange,
indicating standby mode.
will come on for several seconds: ON,
TEMP, and LAMP. Next, the ON
indicator will change to orange,
indicating standby mode.
2
Press the ON/STANDBY
button.
button.
The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-up
screen appears.
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-up
screen appears.
CAUTION
• Do not look into the lens during operation. Doing so could damage your vision.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal
overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could
cause burns, deform/break the object.
Turning the power on and off
Start-up screen
DRAG
R-
C
L
IC
K
L
-C
L
IC
K
AUTO
KEYSTONE
AUTO
SET
PAGE
UP
PAGE
DOWN
FREEZE
MUTE
CALL
ON/STANDBY
LASER
ON/STANDBY
INPUT
MENU
ON
LAMP
TEMP
FAN
AUTO KEYSTONE
AUTO SET
VOL.
+
VOL.
-
Control panel
Remote
Control
COMPUTER IN
MONIT
OR OUT
S-V
IDE
O
VID
EO
AUD
IO IN
AUD
IO O
UT
USB
CON
TRO
L
Before connection
• Read the owner’s manual of the device to be connected to the projector.
• Some types of computer cannot be used connected to this projector.
• Some types of computer cannot be used connected to this projector.
Check for an RGB output terminal, supported signal
, etc.
• Turn off the power of both devices before connection.
• The figure below is a sample connection. This does not mean that all of these devices
• The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Note
• The AUDIO IN terminal is common among all the devices for input terminal.
• On the AUDIO OUT terminal, L and R mixture audio signal (monaural) that volume is
• On the AUDIO OUT terminal, L and R mixture audio signal (monaural) that volume is
adjusted by a projector is output.
• When a plug is inserted to the AUDIO OUT terminal, the projector's speaker outputs no
sound.
Connection
S-VIDEO
VIDEO
AUDIO IN
AUDIO OUT
USB
COMP
U
MONIT
OR OUT
CONTROL
ON
LAMP TEMP
FAN
ON
LAMP TEMP
FAN
(Green) (Green) (Green)
(Off)
(Orange)
(Off)
(Off)
(Off)
S-VIDEO
VIDEO
AUDIO IN
AUDIO OUT
USB
COMPUTER IN
MONIT
OR OUT
CONTROL
Computer
CRT monitor, etc.
To audio
output
output
Audio cable
(for computer)
(supplied)
(for computer)
(supplied)
To RGB
output
output
Control cable
To RS-232C
terminal
terminal
Computer (for control)
RGB cable
(supplied)
To Y/C
B
/C
R
output
Green (Y), Blue (C
B
),
Red (C
R
)
Yellow
(to video output)
(to video output)
To audio
output
White (L)
Red (R)
output
White (L)
Red (R)
VCR
S-Video cable
(not supplied)
(not supplied)
Video cable
(supplied)
(supplied)
To S-Video
output
output
To audio
output
White (L)
Red (R)
output
White (L)
Red (R)
Monitor cable
Mini D-sub 15P-BNC
(not supplied)
Audio cable
(supplied)
DVD player
Conversion
adapter
BNC-pin
(not supplied)
adapter
BNC-pin
(not supplied)
Audio system, etc.
USB cable
(supplied)
To audio
input
White (L)
Red (R)
input
White (L)
Red (R)
To USB
port
port
(Supplied) Power cord connector