Telex BTR-24 Manuel D’Utilisation
1.
Volume Control and Power Switch – Turns the beltpack
power on/off and controls headset volume.
power on/off and controls headset volume.
2.
Battery Light/Power Light – Indicates the beltpack has
power, either from the internal battery or AC power
connected to the unit.
power, either from the internal battery or AC power
connected to the unit.
•
GREEN = Battery Indication: battery OK
•
RED = Battery Low (»15 minutes left)
•
NO Light = Battery Depleted
3.
Button One and Light – Selects audio channel one. The
channel light has two modes depending on the <TALK>
button's state.
channel light has two modes depending on the <TALK>
button's state.
•
Light Solid = Talk and Listen enabled.
•
Light Flashing = Listen only enabled. (Push-to-TX)
4.
Talk Button – Enables the headset microphone. The button
has two modes:
has two modes:
•
Momentary = Pressed and hold for over ½ second.
•
Latch on/off = Tap button and the microphone path is
enabled. Tap again to turn off.
5.
Button Two and Light – Selects Audio channel two. The
channel light has two modes depending on the <TALK>
button's state.
channel light has two modes depending on the <TALK>
button's state.
•
Light Solid = Talk and Listen enabled.
•
Light Flashing = Listen only enabled. (Push-to-TX)
6.
Charge Jack – Used to charge the internal battery or power
unit directly off wall outlet. Accepts a 5.5mm x 2.5mm plug
with the center positive. Must be supplied with a 12VDC
regulated power supply with at least a 400mA current
capacity.
unit directly off wall outlet. Accepts a 5.5mm x 2.5mm plug
with the center positive. Must be supplied with a 12VDC
regulated power supply with at least a 400mA current
capacity.
7.
Charge Light.
•
RED = Beltpack battery is charging.
•
GREEN = Beltpack battery is charged.
8.
Headset Connector – Standard 4-pin XLR connector.
9.
Configuration Jack – RJ-45 jack used to interface the
beltpack to an Ethernet cable. Jack may be used for wired
mode and configuring the beltpack.
beltpack to an Ethernet cable. Jack may be used for wired
mode and configuring the beltpack.
Beltpack Button Combinations (All have voice prompts):
Wireless Mode .................Press <Talk> until unit is done
Wireless Mode .................Press <Talk> until unit is done
booting
Wired Mode .....................Press <TWO> until unit is done
booting.
Master Wireless Mode .....Press <ONE> until unit is done
booting.
Momentary Mode.............Press <ONE> + <TALK> + <TWO>
(Push-to-TX full time)
(Push-to-TX full time)
for 3 seconds. Press the three buttons
again to go back to the default
"Push-to-Latch" mode.
again to go back to the default
"Push-to-Latch" mode.
Microphone Gain .............Press <ONE> + <TALK> for 3
seconds. Keep <TALK> held down
and use <ONE> to decrease the gain,
<TWO> to increase it. Release all
buttons for at lease 1 second to set.
and use <ONE> to decrease the gain,
<TWO> to increase it. Release all
buttons for at lease 1 second to set.
Sidetone Level..................Press <TALK> + <TWO> for 3
seconds. Keep <TALK> held down
and use <ONE> to decrease the
level, <TWO> to increase it. Release
and use <ONE> to decrease the
level, <TWO> to increase it. Release
all buttons for at least 1 second to set.
Section 3 - TR-24 Beltpack
Controls and Connections
1 2 3
OFF
MIC
S.T.
A J
D
1
2
4 5
A J
D
3-1
CHG
EXT
6 7 8
9
Top View
Bottom View
(1) Microphone
Shield (-)
Shield (-)
(2) Microphone
Audio (+)
Audio (+)
(3) Headphone
High (+)
High (+)
(4) Headphone
Low (-)
Low (-)