Samsung n/a Manuel D’Utilisation
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
7
INSTALLATION & MAINTENANCE
•
If the washer is not leveled with the ground, it makes the machine tremble more or be out of order.
So, make sure that the washer is leveled properly.
ENVIRONMENT
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface,
noise or vibration occurs. (Allowable is 1˚)
Adjust the legs for even placement.
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface,
noise or vibration occurs. (Allowable is 1˚)
Adjust the legs for even placement.
Never install the washer near water.
Do not place the washer in steamy rooms or where the
washer is directly exposed to rain.Moisture may destroy the
electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by direct
heat,never place the washer near furnaces, boilers, etc.
Do not place under direct sunlight.
Do not place the washer in steamy rooms or where the
washer is directly exposed to rain.Moisture may destroy the
electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by direct
heat,never place the washer near furnaces, boilers, etc.
Do not place under direct sunlight.
LEVELLING
Lock
Loosen
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING
THE POSITION OF THE WASHING TUB.
THE POSITION OF THE WASHING TUB.
1. Adjust the side horizontally
first and the front
in same direction
in same direction
❷
next.
2. If the thread is not
within the limit, adjust
the height of
the legs.
the height of
the legs.
•
Open the lid of the machine, pour water into the tub up to the level
just below the pulsator, and adjust the legs so that the pulsator is
positioned at the center of the water as shown in the figure.
positioned at the center of the water as shown in the figure.
•
Place the machine more than
10cm away from the wall.
•
Adjust the legs on feet
for levelling .
1. Remove the adaptor
from the water
supply hose.
supply hose.
2. First,using a "+" type
screw driver, loosen the
four screws on the adaptor.
Next,take the adaptor and
turn part(b) following the
arrow for gap about 5mm
between them.
four screws on the adaptor.
Next,take the adaptor and
turn part(b) following the
arrow for gap about 5mm
between them.
3. Connect adaptor to the
water tap by tightening
the screws firmly.
Then, turn part (b)
following the arrow and
put (a) and (b)together.
the screws firmly.
Then, turn part (b)
following the arrow and
put (a) and (b)together.
a
b
a
b
c
CONNECTING THE WATER SUPPLY HOSE
4. Connect the water supply
hose to the adaptor. Pull down
the part (c) of the water supply
hose .When the part (c)is released,
the hose is automatically
connected to the adaptor
making a 'click' sound.
the part (c) of the water supply
hose .When the part (c)is released,
the hose is automatically
connected to the adaptor
making a 'click' sound.
5. Connect the other end of the water
supply hose to the inlet water valve
at the back of the washer.
Screw the hose clockwise all the
way in.
at the back of the washer.
Screw the hose clockwise all the
way in.
NOTICE After completing connection, if water leaks from the hose,
then repeat the same steps.
Use the most conventional type of faucet for water supply.
In case the faucet is square or too big,remove the spacing
ring before inserting the faucet into the adaptor.
then repeat the same steps.
Use the most conventional type of faucet for water supply.
In case the faucet is square or too big,remove the spacing
ring before inserting the faucet into the adaptor.