GE 19216 Fascicule

2. Before mounting, choose a mounting location that

is not farther than 150 feet from the chime unit

location.

Not further than 150 feet 

3. Before placing the pushbutton where you would like

to mount it, place the chime as close to final position 

as possible. Test the operation before drilling. If it

works, mount the push button. If it does not work,

see TROUBLESHOOTING.

4. Use back cover of push button as a template to mark

two screw holes.

5. Drill two holes with 1/16” size drill in marked

locations.

6. Secure back cover to the mounting surface with two

supplied mounting screws.

7. Install the supplied 12V battery observing proper

polarity. (see battery installation section)

8. Press front housing onto back cover.

9. Test operation. If the chime does not work, see

TROUBLESHOOTING.

If you do not want to drill holes in your door frame, you

can use the supplied double sided tape for installation.

1. Clean all mounting surfaces with a 50/50 mixture of

isopropyl alcohol.

2. Remove the backing from one side of the double

sided tape and press the exposed side against the

back plate of the push button.

3. Remove the other backing strip and press the

exposed side against the door frame where you want

the button installed.

1. Plug the chime into a 120V AC outlet and slide the

power switch to the “On” position to turn on the

chime. The red LED power indicator will light.

GE Model 19216

www.jascoproducts.com

(2) 3x20mm screws

(1) Double sided adhesive pad

The wireless door chime kit has two components:

Battery Operated

Chime (Receiver)

PushButton (Transmitter)

Plugs into 120V outlet  Battery included

All wireless chimes may have more than one push

button. The chime tune for each push button is set with

dip switches 1-3. Located inside the push button.

Single Push Button Kit: If you purchased a kit with a

single push button, the chime tune will be set to Ding

Dong from the factory.

Dual Push Button Kit: If you purchased a kit with two

push buttons, one push button will be set to Ding Dong

and the other push button will be set to Westminster

from the factory.

The following instructions explain how to change the

tune on any wireless push button.

1. Remove the cover from the push button - see

wireless push button battery.

2. Remove the battery from the push button transmitter.

3. Locate the 3 dip switches shown below.

4. Select the desired chime sound from the table below.

Westminster

ON

OFF

OFF

Ding Dong

OFF

ON

OFF

Knock

OFF

OFF

ON

Bronze Chime  ON

ON

OFF

Cuckoo Clock

ON

OFF

ON

Foghorn

OFF

ON

ON

Gong

ON

ON

ON

Pushbutton House Code Jumpers Chime Dip Switches

Pushbutton Dip Switches and Jumpers

Each chime component has 4 jumpers for setting the

house security code. In most cases you will not need

to change the factory settings for the house security

code. If your chime activates intermittently or does not

work at all, you may be able to solve the problem by

changing your security code.

The chime and pushbutton must be set to the same

house security code for the combination to operate

together.

1. Remove power from the chime.

2. To remove the batteries from the pushbutton, open

the pushbutton case as shown below.

3. Locate the House Security Code door and screw

located on the back of the Chime. Remove the

screw and take off the door.

4. Locate the chime and pushbutton jumpers shown

above.

5. To change the house code, add or remove jumpers

as needed. It is recommended to change only one

jumper at a time and then test the system for proper

operation. The jumpers on the chime and pushbutton

must match exactly.

To install or replace the battery in the wireless push

button.

1. Remove the back cover of the push button.

2. Install the A23 (12 volt) battery with the negative

side of the battery (-) toward the spring and the

positive side of the battery (+) toward the positive

battery holder as shown below.

3. Replace back cover as shown below.

Push Button Mounting Instructions

Note: Avoid mounting on metal surfaces, as it may

result in a reduced range of transmission. Do not mount

in an area where exposed to direct rain.

a. Removing the back cover

b. Replacing the back cover

1. Push buttons are typically mounted at the same

height as the door knob or handle (between 36” and

44” above the floor).

2. Gently press transmitter button to sound chime.

Chime doesn’t work:

1. Make sure push button switch is depressed and held

for at least 1 second.

2. Make sure house code switches 1-4 on chime and

push button match exactly.

3. Verify battery orientation in push button.

4. Try fresh batteries.

5. Make sure chime is not farther than 150 feet away

from push button.

6. Ensure push button is not mounted on metal, near

metal studs, or near the floor. 

7. Try a new location for the chime.

Functional range may be adversely affected by one or

more of the following factors: weather, radio frequency

interference, low transmitter battery and obstructions

between the transmitter and receiver.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept interference received,

including any interference that may cause undesired

operation.

Made in China

is a trademark of

General Electric Company

and is used under license to

Jasco Products Company LLC,

10 E. Memorial Rd.,

Oklahoma City, OK 73114.

www.jascoproducts.com

Rev. 10-07

19216

Chime Dip

Switches

Pushbutton

House Code

Jumpers

Chime Dip

Switches

Pushbutton

House Code

Jumpers

Pushbutton Jumpers

4

5

6

8

Power Indicator

On/Off Switch