Panasonic KX-TG7103NE Manuel D’Utilisation
Multi-unit Operation
20
Operating additional units
Additional handsets
Up to 6 handsets can be registered to the base
unit. Additional handsets will give you the
freedom to, for example, have an intercom call
with another handset while a third handset is on
an outside call. See side 5 for information on
ordering additional handsets.
Vigtigt:
L
unit. Additional handsets will give you the
freedom to, for example, have an intercom call
with another handset while a third handset is on
an outside call. See side 5 for information on
ordering additional handsets.
Vigtigt:
L
The additional handset model recommended
for use with this unit is noted on side 5. If other
model handset is used, certain operations
(handset settings, base unit settings, etc.) may
not be available.
for use with this unit is noted on side 5. If other
model handset is used, certain operations
(handset settings, base unit settings, etc.) may
not be available.
Registering a handset to the
base unit
base unit
The included handset and base unit are
preregistered. If for some reason the handset is
not registered to the base unit (for example, w
flashes even when the handset is near the base
unit), register the handset manually (side 20).
preregistered. If for some reason the handset is
not registered to the base unit (for example, w
flashes even when the handset is near the base
unit), register the handset manually (side 20).
To register an additional handset to the base
unit (easy registration)
After purchasing an additional handset, register it
to the base unit. Ensure that the additional
handset is switched on. If it is not on, press and
hold {ih} for few seconds to turn the handset
on.
unit (easy registration)
After purchasing an additional handset, register it
to the base unit. Ensure that the additional
handset is switched on. If it is not on, press and
hold {ih} for few seconds to turn the handset
on.
1
Lift the additional handset and press {ih}
to put the handset in standby mode.
to put the handset in standby mode.
2
Press and hold {x} on the base unit for
about 3 seconds, until the registration tone
sounds.
about 3 seconds, until the registration tone
sounds.
3
Place the additional handset on the base
unit. The registration tone continues to
sound. With the handset still on the base
unit, wait until a confirmation tone sounds
and w stops flashing.
unit. The registration tone continues to
sound. With the handset still on the base
unit, wait until a confirmation tone sounds
and w stops flashing.
Bemærk:
L
L
If an error tone sounds, or if w is still flashing,
register the handset manually (manual
registration; side 20).
register the handset manually (manual
registration; side 20).
L
L
Charge the batteries of your additional handset
for about 7 hours before initial use.
for about 7 hours before initial use.
L
This registration method cannot be used for
handsets that have already been registered to
the base unit. Register the handset manually
(manual registration; side 20).
handsets that have already been registered to
the base unit. Register the handset manually
(manual registration; side 20).
To register a handset to the base unit (manual
registration)
You can register a handset to the base unit
manually using the following method.
registration)
You can register a handset to the base unit
manually using the following method.
1
{j
/OK} i “Indstil håndsæt” i {>}
2
“Registrering” i {>}
3
“Reg.Håndsæt” i {>}
4
Press and hold {x} on the base unit for
about 3 seconds, until the registration tone
sounds.
L
about 3 seconds, until the registration tone
sounds.
L
If all registered handsets start ringing,
press {x} to stop, then repeat this step.
press {x} to stop, then repeat this step.
L
After pressing {x}, the rest of this
procedure must be completed within 1
minute.
procedure must be completed within 1
minute.
5
Wait until “Indt. base PIN” is displayed,
then enter the base unit PIN (default:
“0000”), then press {j/OK}.
L
then enter the base unit PIN (default:
“0000”), then press {j/OK}.
L
When the handset has been registered
successfully, w will stop flashing. If
keytones are turned on (side 15), a
confirmation tone will be heard.
successfully, w will stop flashing. If
keytones are turned on (side 15), a
confirmation tone will be heard.
Cancelling a handset
A maximum of 6 handsets can be registered to
the base unit. A handset can cancel its own
registration (or the registration of another
handset) that is stored in the base unit. This will
allow the base unit to “forget” the handset.
the base unit. A handset can cancel its own
registration (or the registration of another
handset) that is stored in the base unit. This will
allow the base unit to “forget” the handset.
1
{j
/OK} i “Indstil base” i {>}
2
Enter “335”.
3
“Slet Håndsæt” i {>}
TG7100-7102-7103NE(e-da).book Page 20 Wednesday, April 19, 2006 1:09 PM