Oracle Audio Technologies OFD-614 Manuel D’Utilisation
Model OFD-614
5/4/2006
Patents Pending
2.1
A.
C.
2.1
C.
ACTIVATING THE OFD WITH A REPEATER
(WITHIN AN EXISTING NETWORK)
ACTIVATING THE OFD WITH AN ORACLE PORTABLE
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
B. ACTIVATING THE OFD WITH A FLUSH MOUNT
ACTIVATING AN INTERCOM NETWORK
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
ACTIVATING AN INTERCOM NETWORK - CON'T
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
- 8 -
- 5 -
B. ACTIVATING ADDITIONAL INTERCOM UNITS BACK INTO THE NETWORK
Note: Both steps 1 & 2 must occur within 15 seconds of each other.
ACTIVATING THE OFD WITH AN OTIU
To set a FrontDoor unit to Passive Mode, switch dipswitch #1 UP (away from the circuit
board).
Note: Any Intercoms that had been taught to this unit will have to have their memory cleared
and be re-taught to the Active Unit in the network as if they were newly installed.
Note: Both steps 1 & 2 must occur within 20 seconds of each other.
board).
Note: Any Intercoms that had been taught to this unit will have to have their memory cleared
and be re-taught to the Active Unit in the network as if they were newly installed.
Note: Both steps 1 & 2 must occur within 20 seconds of each other.
1.
To activate the Passive FrontDoor, press the LEARN button inside the
FrontDoor unit for a second (until you hear a beep) and release it.
FrontDoor unit for a second (until you hear a beep) and release it.
2.
Enter the Master PIN number on the GAP:
For example:
For example:
Then enter:
After the “BEEP” press “CALL”.
After the “BEEP” press “CALL”.
3.
You will hear a tone indicating a successful activation.
4. Proceed to Section 3
1 2 3 4
0 5
1.
To activate the Passive FrontDoor, press the LEARN button inside the FrontDoor
unit for a second (until you hear a beep) and release it.
unit for a second (until you hear a beep) and release it.
2.
Press the LEARN button on ONE of the Repeater Units. The LED by the LEARN
button will light up for several seconds and then will go out, indicating a successful
activation.
button will light up for several seconds and then will go out, indicating a successful
activation.
3. Proceed to Section 3
(See next page for an example of an existing network with an OFD and Repeater).
1.
Press and release the LEARN button on an Oracle Portable Intercom
(OPI).
(OPI).
2. Press the LEARN button inside the FrontDoor unit for a second (until
you hear a beep) and release. The OPI will sound a tone indicating a
successful activation.
successful activation.
3. Proceed to Section 3
1.
On a Flush Mount Intercom, hold down both buttons for 3 seconds,
until the channel lights start flashing quickly.
until the channel lights start flashing quickly.
2.
Press the LEARN button inside the FrontDoor unit for a second (until
you hear a beep) and release. The Flush Mount will sound a tone
indicating a successful activation.
you hear a beep) and release. The Flush Mount will sound a tone
indicating a successful activation.
3. Proceed to Section 3
Note: If used in location that will be below -10°C (20°F) Lithium batteries are
recommended.
The FrontDoor must be taught to an intercom to form an intercom network, or must be
taught into an existing network (See “Activating into an Existing Intercom Network”).
The FrontDoor is fully compatible with other Oracle System Intercoms.
taught into an existing network (See “Activating into an Existing Intercom Network”).
The FrontDoor is fully compatible with other Oracle System Intercoms.
1.
Press and release the LEARN button on an un-activated Oracle Intercom
(On a Flush Mount Intercom hold down both buttons for 3 seconds, until the
channel lights start flashing quickly).
(On a Flush Mount Intercom hold down both buttons for 3 seconds, until the
channel lights start flashing quickly).