Panasonic KX-TCD700AL Manuel D’Utilisation
38
Registration
• Register a Handset to a Base Unit (r
re
eg
gi
is
st
te
er
r
h
hs
s
)
The handset supplied with the base unit is already registered. If an optional
handset/base unit is purchased, the following procedure needs to be carried out
before initial use.
handset/base unit is purchased, the following procedure needs to be carried out
before initial use.
Z
and Hold
Ï
on base unit for 10 secs.
-1-888888
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
(Standby Mode)
new speed
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
Z Y
or
V
setting hs
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
Z S
or
U
Z S
or
U
Z Y
or
V
Z
Y
or
V
time alarm
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
registration
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
Z
Y
or
V
base 2
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
S U
base 4
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
• Select base unit.
Z Y
Z Y
or V
• (“Hyphen” is moving during
searching).
Connection OK.
• Enter PIN
(4 digits).
• Base is found.
• On completion of
• On completion of
registration, a
confirmation tone
sounds.
confirmation tone
sounds.
• If registration is not
successful within 5
minutes, an error tone
sounds and display
returns to original
standby mode.
minutes, an error tone
sounds and display
returns to original
standby mode.
Z Y
(Searching Base).
bs
9
pin É
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
88
-
888888888
Â
Ê
Á
Ë
È
Í
Q
Ï Ô Ó
Ò
-2-
8888888
01
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
register hs
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
S U
cancel base
Â
Ê
Á
Ë
È
Í
Î
Ï Ô Ó
Ò
NOTES:
• Charge the optional handset batteries for about 10 hours
• Charge the optional handset batteries for about 10 hours
before initial use.
• Register the handset number within 1 minute. If not
registered within 1 minute, ZP on the handset to
cancel the programming mode. Then re-start registration.
cancel the programming mode. Then re-start registration.
• Calls (both incoming and outgoing) can be conducted only
via the displayed base unit (even if the radio areas overlap
with neighbouring base units).
with neighbouring base units).
Note:
• To return to the previous step during programming, Z T.
• To return to the previous step during programming, Z T.
• To exit the programming mode at any time, Z P.
See page 39
700al australian 2 5 02 2/5/02 3:00 pm Page 38