AT&T 6434 Manuel D’Utilisation
EXIT/NORMAL (display feature)
When you are ready to leave Display or Softkey
Mode and return to Normal (call-handling) Mode
Mode and return to Normal (call-handling) Mode
1
Press [
Exit
].
HOLD
To put a call on hold
1
Press [
Hold
].
To answer a new call while active on another
1
Press [
Hold
].
2
Press call appearance button of incoming call.
To return to held call
1
Press call appearance button of held call.
INSPECT (display feature)
To see who is calling while on a call
1
Press [
Inspect
].
●
Call source is shown on display.
2
Press [
Exit
] to return to display for present call.
LAST NUMBER DIALED
To automatically redial the last number you
dialed
1
Press [
LastDialed
]
or Dial Last Number Dialed access code
.
LEAVE WORD CALLING (LWC)
To leave a message after dialing an extension
1
Press softkey below LWC
or Press [
LWC
] before hanging up your handset.
6
To leave a msssage without ringing an extension
1 While off-hook press softkey below LWC
or Press [
LWC
]
or Dial Leave Word Calling access code
.
2 Dial extension.
3 Hang up.
To cancel a Leave Word Calling message
1
2
While off-hook press the softkey below CnLWC
or Press [
or Press [
Cancel LWC
]
or Dial Leave Word Calling cancel code
.
Dial extension.
PRIORITY CALLING
To place a priority call (3-burst ring)
1 While off-hook press the softkey below PCall
or Press [
Priority
]
or Dial Priority Calling access code
.
2 Dial extension.
RESET SPEAKERPHONE
To adjust the speakerphone to the surrounding
room acoustics
1 While on-hook, press [
Shift
] and then
press [
Speaker
].
●
You hear a series of tones.
SELECT RING (and RINGER VOLUME)
To select a personalized ring
1
2
3
Press [
Shift
] and then press [
Hold
].
●
Current ringing pattern plays, and pattern
number is displayed.
To cycle through all eight ring patterns, continue to
press (and then release) [
Hold
] (or press
[
N e x t >
] or [
< P r e v
]).
When you hear the desired ring pattern, press
[
Shift
] again.
7
To adjust ringer volume if necessary (speaker is
not active)
1
To raise the volume, press the right half of the
Volume control button labeled [
∧∧
];
to lower the volume, press the left half of the
Volume control button labeled [
∨∨
]
SEND ALL CALLS
To send all calls (except priority calls) immediately
to coverage
to coverage
1
Press [
Send Calls
]
or Dial Send All Calls access code
.
To cancel Send All Calls
1
While off-hook, press [
Send Calls
] again
or Dial Send All Calls access code
.
SPEAKERPHONE
NOTE: To use this feature, your voice terminal must
be set for the Speakerphone (speak and listen)
be set for the Speakerphone (speak and listen)
feature.
To place or answer a call without lifting the
handset, or to use speakerphone with any feature
1
Press [
Speaker
].
2
Place or answer call, or access selected feature.
3
Adjust speakerphone volume if necessary:
To raise the volume, press the right half of the
Volume control button labeled [
Volume control button labeled [
∧∧
];
to lower the volume, press the left half of the
Volume control button labeled [
Volume control button labeled [
∨∨
].
To prevent the other party from hearing you
1
Press [
Mute
].
●
Red Mute light goes on.
2
Press [
Mute
] again to resume talking to party.
●
Red Mute light goes off.
8