Toshiba 42H83 Manuel D’Utilisation
Intr
oduction
Connecting
y
our T
V
Using the
Remote Contr
ol
Setting up
y
our T
V
Using the T
V’s
F
eatur
es
Appendix
Index
16
1
2
3
4
5
6
7
8
9
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
PIC SIZE
EXIT
LIGHT
STOP SOURCE
ADV/
POP CH
ADV/
POP CH
FAV
FAV
PLAY PIP
REC
TV/VCR
REW
FF
STILL
LOCATE SWAP
FAVORITE
MENU/
C.CAPT
ENTER
Note:
• Each time you replace the batteries, you
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch, and
does not respond to any of the codes for
your VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
does not respond to any of the codes for
your VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
POWER
Channel
yz
Channel
Number
Number
Enter
RECALL
To control a cable TV converter:
Set the TV/CABLE/VCR switch to the CABLE position.
The shaded buttons shown at right will control the cable TV
converter.
The shaded buttons shown at right will control the cable TV
converter.
Programming the remote control
The remote control is preprogrammed to operate most Toshiba
devices. To program the remote control to operate a non-Toshiba
device or a Toshiba device that the remote control is not
preprogrammed to operate:
devices. To program the remote control to operate a non-Toshiba
device or a Toshiba device that the remote control is not
preprogrammed to operate:
1. Refer to the “VCR code table” or “Cable TV converter code
table” on pages 17–18 to find the code for your VCR or
converter.
If more than one code is listed, try each one separately until you
find one that works.
converter.
If more than one code is listed, try each one separately until you
find one that works.
2. If you are programming the remote control to operate your:
• VCR, set the TV/CABLE/VCR switch on the remote control
to VCR.
• Cable converter, set the TV/CABLE/VCR switch on the
remote control to CABLE.
3. While holding down the RECALL button, press the Number
buttons (0–9) to enter the three-digit code for your brand of
VCR or converter.
VCR or converter.
4. Point the remote control at the VCR or converter and press
POWER to test the code.
If the VCR or converter turns on, you have entered the correct
code.
If the VCR or converter turns on, you have entered the correct
code.
Note: In addition to POWER, confirm that all necessary keys on the TV
remote control operate your device. If some keys are not operational,
repeat the device code setup using another code (if other codes are
listed for your device). If, after trying all listed codes, the necessary keys
do not operate your device, use the device’s original remote control.
remote control operate your device. If some keys are not operational,
repeat the device code setup using another code (if other codes are
listed for your device). If, after trying all listed codes, the necessary keys
do not operate your device, use the device’s original remote control.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong code. Repeat steps 1–4 with
another code.
you may have entered the wrong code. Repeat steps 1–4 with
another code.
5. Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the codes you used:
VCR code
_____________________
Cable code
_____________________