Panasonic LB20NTU Manuel D’Utilisation
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
to securely tighten the lamp
unit cover fixing screws.
( Connect the power cord.
) Press the POWER button so
that a picture is projected onto
the screen.
the screen.
* Press the MENU button to
display the “MAIN MENU”, and
then press the F or G button
to select “OPTION”.
then press the F or G button
to select “OPTION”.
E
NGLISH
-57
Care
and
m
aintenance
+ Press the ENTER button to
display the “OPTION” menu, and
then press the F or G button to
select “LAMP RUNTIME”.
then press the F or G button to
select “LAMP RUNTIME”.
, Press and hold the ENTER
button for approximately 3
seconds.
seconds.
The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.
change to “TIME RESET
[POWER OFF]”.
- Turn off the power and
disconnect the power cord.
This will reset the cumulative
usage time for the lamp unit to “0”.
Refer to page 26 for details on
how to turn off the power.
This will reset the cumulative
usage time for the lamp unit to “0”.
Refer to page 26 for details on
how to turn off the power.
M E N U
K E Y S T O N E
P I C T U R E
P O S I T I O N
I N D E X W I N D O W
S H U T T E R
V O L U M E
L A N G U A G E
O P T I O N
S E C U R I T Y
N E T W O R K
S E L E C T E N T E R E X I T
O P T I O N
▲
B A C K C O L O R B L U E
F R O N T / R E A R F R O N T
D E S K / C E I L I N G D E S K
F A N C O N T R O L S T A N D A R D
L A M P P O W E R H I G H
T I M E R E S E T [ P O W E R O F F ]
F U N C 1 D A Y L I G H T
C O N T R O L K E Y O N
A U T O P O W . O F F D I S A B L E
P O W E R M E M O R Y O N
S E L E C T R E T R N
NOTE:
B Be sure to install the lamp unit
B Be sure to install the lamp unit
and the lamp unit cover
securely. If they are not securely
installed, it may cause the
protection circuit to operate so
that the power cannot be turned
on.
securely. If they are not securely
installed, it may cause the
protection circuit to operate so
that the power cannot be turned
on.
NOTE:
B If the MENU button is pressed,
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
will be cancelled.
NOTE:
B If the power cord was
B If the power cord was
disconnected during projection
when the projector was used
the last time, projection will
start after the power cord is
connected (when “POWER
MEMORY” in the “OPTION”
menu is set to “ON”). Refer to
page 48 for details.
when the projector was used
the last time, projection will
start after the power cord is
connected (when “POWER
MEMORY” in the “OPTION”
menu is set to “ON”). Refer to
page 48 for details.
O P T I O N
▲
B A C K C O L O R B L U E
F R O N T / R E A R F R O N T
D E S K / C E I L I N G D E S K
F A N C O N T R O L S T A N D A R D
L A M P P O W E R H I G H
L A M P R U N T I M E 1 8 2 0 H
F U N C 1 D A Y L I G H T
C O N T R O L K E Y O N
A U T O P O W . O F F D I S A B L E
P O W E R M E M O R Y O N
S E L E C T R E T R N